Hi i have a GA-Z97X-SOC Force (rev. 1.0) motherboard (this motherboard do not have M.2 socket), i completly noobhead about moding/changing BIOS, i purchase PCIe Adapter to "Samsung 1TB SSD 980 PRO M.2 PCIe 4.0 MZ-V8P1T0 NVMe internal Solid State Drive", but i dont know how to change my BIOS to can boot windows from my PCIe port when i isert adapter with my drive. Can sameone help me?
U came here to this thread...but didnt bother to read a bit of the guide posted? Look again and check point #4 of OS installation.
Donations via PAYPAL / REVOLUT, if u think the guy deserves it, else to the Win-Raid community on the bottom of the page, as it deserves for all the gathered information.
Zitat von MeatWar im Beitrag #7066U came here to this thread...but didnt bother to read a bit of the guide posted? Look again and check point #4 of OS installation.
is looking like u are mad person. Offcourse i read everything and i do not undestand 80% of this. My BIOS not read my SSD from PCIe, when i install windows on it (with pluged another SSD to Sata), and doesnt matter i turn off that Sata port or no, i can not finish instalation, i spend 15 hour yestrday to find a solution and u said to me i do not read the post? Fantastic !
Yes it is, already factory AMI NVMe supported and that was not ur initial question, go read. Until u get a full UEFI/GPT OS on it, ur old SATA OS is the primary boot in system, disconnect all drives of the system, prepare the USB OS installer, upon OS setup the NVMe drive will appear as destination, finish. Shutdown, reconnect old drives, set boot priority in bios to the new OS if necessary, save and exit, ur done.
Donations via PAYPAL / REVOLUT, if u think the guy deserves it, else to the Win-Raid community on the bottom of the page, as it deserves for all the gathered information.
When I unplug all SATA devices and all USB, and left just my USB flash with OS instalation i have that one When i unplug my USB with OS, in boot section i have completly nothing: So i plug it and i going to windows instalation, windows find my device/disc i create 2 particions and wanna install windows on 1 of them and i get error "We couldn't create a new partition or locate an existing one." (is polish windows, i dont have a ENG one). Is looking like factory AMI NVMe is not supported or i do something wrong.
Edit by Fernando: Via incomplete links inserted pictures downloaded, resized and inserted by using the Forum software
@Jack284: Welcome to the Win-RAID Forum! Your inserted pictures verify, that you didn't exactly follow my guide regarding the Rufus GUI settings. The OS has to be installed by using the GuiMode Partition Table (GPT). So you have to repeat the preparation of the USB Flash Drive as described within my guide. When the OS Setup comes to the point, where you have to determine the target location for the OS, you have a) to delete all shown partitions of the NVMe SSD, b) to let the Setup create the target OS partition, c) to wait until the Setup has finished the creation of the other 2 (usually hidden) partitions and d) to install the OS onto the partition, which has already been pre-selected (highlighted) by the OS Setup. By the way: 1. Within >this< Sub-Forum you can find Guides about how to make a screenshot of the just opened window and how to insert the picture into the Forum. 2. Usually the BIOS offers an option to take a screenshot and store the file onto an attached USB Flash Drive by pressing F12 (looks much better than a photo). 3. Question: Are you sure, that the BIOS contains the required NVMe module? How did you insert it and how did you flash the modded BIOS? Good luck! Dieter (alias Fernando)
My current System: MB: ASRock X570 Pro4, CPU: AMD Ryzen 5 5600X, System Drive: 1 TB Samsung 980 Pro, Graphics: Sapphire Radeon RX570, OS: Win11 x64 Pro Donation Link: If you are satisfied with my Forum activities, you can send me a donation by clicking onto >this< or >this< link.
@Jack284@MeatWar@lfb6 Since the topic of the request and its discussion has not much to do with the thread, where they were originally posted, I have moved all your topic related posts into the Win10 Sub-Forum.
My current System: MB: ASRock X570 Pro4, CPU: AMD Ryzen 5 5600X, System Drive: 1 TB Samsung 980 Pro, Graphics: Sapphire Radeon RX570, OS: Win11 x64 Pro Donation Link: If you are satisfied with my Forum activities, you can send me a donation by clicking onto >this< or >this< link.
Print view
Today 5:05 am (Last edited: 6 minutes ago )
reply
Win-Raid Forum (Drivers - Firmware - Modding)
»
OS related Topics
»
Windows 8-10/Server 2012-2019
»
How to get Win10 installed onto an NVMe SSD?
