Hello there. I have a Lenovo V570c notebook and the VBIOS version is 2108.5. I want to upgrade to 2170 version and insert GOP driver. How am I going to do this? Thank you to everyone who helped. :)

Files:

I have replaced orom vbios 1049 to 1059 and the uefi does not recognize 1059 just 1047.


How should i do to fix that.
Im succesfull replace my gop intel from 9.1056 to 9.1102


When i check my bios version on intel using gpu z he showing PC 1070.

How to find this guid using uefitool?
Im done replaced all the raw gop vbt, gop, vbios orom and test using ubu the information is correct, but after flashing using fpt the vbios doesnt changed.

I have done updated from raw gop vbt from 209 to 228 but im not sure how to check the detailed on actual bios.
The information on ubu tools just corrected using sonix guide's
Thanks in advance.

Hello and thanks for the guide.

I am trying to update Coffelake VBIOS from 1008 to 1019

VBT version is D1/2.09 and size of VBT is 109C/4252 so from the included table these are correct.

On the guide it says this.

Zitat

---

*3) If the BSF-script file to the desired version is not present, refer to the table to find the compatible. To do this, we have data on the version and size of VBT.
See the attached file 'Table VBT OROM VBIOS Version and Size.docx'

---

On the "Table VBT OROM VBIOS Version and Size" there is a note

Zitat

---

For CFL_1019 abd CFL_1023 use CloneVBT:
1007 – 1018 -> 1019
1020 – 1024 -> 1025

---

I haven't understood the CloneVBT part. From what i understand I will use CloneVBT.exe like this

c:\>CloneVBT.exe biosv.dat cfl_1019.dat
       | $VBT Name       | Version | Size       | Type | Build |
-------+-----------------+---------+------------+------+-------+
Source | COFFEELAKE      | D1  209 | 109C  4252 | OROM | 1008  |
Target | COFFEELAKE      | D1  209 | 109C  4252 | OROM | 1019  |
Cloning...
Done.
Press any key to continue . . .
 

After doing this I have the cln_vbios.bin file. Continuing that part needs bsf file but in the given Intel_VBIOS_and_BSF_r3\CFL\1019 (VBIOS 1019) folder there are none...

For the above guide next step of 4) I install the program. On the 5th step I still don't have a bsf script file how will i use the IBMP program without the script because it asks on launch.
Thanks for your time :)

@berkkocaturk

If you use CloneVBT, then all settings will be transferred 1 to 1 and nothing else needs to be done, just replace the VBIOS in the BIOS.

That certainly makes it easier I though about that but wasn't sure.

Thanks a lot for the programs and the guide.

I'm sorry to bother you, but I'm a little confused about GOP-VBT updating.
My motherboard is ASRock B360M (OEM customized) and I am trying to update GOP-VBT with the BIOS file dumped from the mobo.
The figure below shows it's <1>"VBIOS.dat"(OROM) extracted by MMTool based on your 2) explanation, and <2>"old_vbt.dat" extracted by UEFITool(alpha 58) based on your explanation 2) in "Alternative method".

<1> said that the chipset seriese is "COFFEELAKE", VBT version is "D1"(=209), size is "109C"(=4252 byte), and OROM version is 1008.
And (this may not be relevant), <2> showed "SKYLAKE", "D4"(=212), size:1128(=4392).
Then I searched for "COFFEELAKE" in the original dumed BIOS, but I couldn't find the word, but "SKYLAKE" was found instead.
Where did the "COFFEELAKE" in "VBIOS.dat" come from?
In any case, I tried both CFL / 212 > 228 and SKL_KBL / 209 > 228 to convert with iBMP following your instruction.
As a result, the following warning was displayed and the conversion could not be performed.:

In the case of this motherboard, what file should I choose and what steps should I take to process it?
Reading #453 post, I also tried using clonevbt following your "Alternative method" explanation, but it didn't output any files.
I have been suffering from this for over a week already.
Thank you for any help.

Not new, seems that from 221 to 228 several settings disappeared, or syntax was changed, see:
[Guide] Transfer of specific Intel OROM VBIOS and GOP VBT settings by using Intel BMP tool (30)

I think Lost_N_BIOS stayed at 221 this time, but I'm not completely sure. If you want to build 228 you'd have to check for every error displayed if it's a new syntax ot if this setting no longer exists. Not clear if result will work though.

Thanks for your prompt comment.
As you say, SKL_KBL\209 > 221 was able to convert without any error.
So I compared both script files (* .bsf).
As a result, I found that some of the symbols defined in 209 where the error occurred are absent or "SKIP" in 228.

Perhaps copying this bit to copy (the line "$ PM_DPST_Enable" in the example figure) might solve this problem with this symbol.
The bit position of all error symbols is "SKIP" and I hope it can be replaced.
Also, just because I transferred a symbol that doesn't exist in the 228 * .bsf file, it's likely that it won't be used in the actual BIOS.
(That is, I think I can delete all error-corresponding lines in the original 209 .bsf file.
I will check this matter (delete all corresponding line) later.)
Does anyone know or already try how to handle such cases?
Anyway, I got the BIOS file with the VBT updated to 221 (the PC that wrote the BIOS is working fine now), so I'm very grateful to you for this.

Zitat von impossible_jp im Beitrag #458

---

Thanks for your prompt comment.

Perhaps copying this bit to copy (the line "$ PM_DPST_Enable" in the example figure) might solve this problem with this symbol.
The bit position of all error symbols is "SKIP" and I hope it can be replaced.

---

I think Sonix changed structure in files folder a little. Look into the folders \Files\intel\VBIOS, \Files\intel\GOP_VBT and Files\intel\GOP\Usr_GOP\, there's a _readme with naming convention, try what UBU says.

(In my opinion tt would be more interesting to see what happens if one just deletes the obsolete lines.)

But is this the board?
https://www.asrock.com/mb/Intel/B360M-ITX/index.asp#BIOS

If so: Latest bios has GOP 228, it's just to compare which settings ASrock used?

Hi, lfb6.
Thanks for your comment.

Zitat von lfb6 im Beitrag #460

---

I think Sonix changed structure in files folder a little. Look into the folders \Files\intel\VBIOS, \Files\intel\GOP_VBT and Files\intel\GOP\Usr_GOP\, there's a _readme with naming convention, try what UBU says.
(In my opinion tt would be more interesting to see what happens if one just deletes the obsolete lines.)
But is this the board?
https://www.asrock.com/mb/Intel/B360M-ITX/index.asp#BIOS
If so: Latest bios has GOP 228, it's just to compare which settings ASrock used?

---

Can someone link a download to GOP VBT 221?

Fixed download link

I updated my vbios with the BMP method. But now my aspect ratio changed from 16:9 to 4:3 on startup. I've created a post: www. win-raid .com / t8729f16-Success-BUT-HELP-VBIOS-on-Laptop-updated-Aspect-Ratio-changed-how-to-correct.html
(Remove spaces from link to open)

@SoniX

I have IVY but MMTool shows me IVB-102 is that normal?

Zitat

---

For Desktop DevID SNB-102, IVB-162, HSW/BDW-402,412,c02,c12

---