Ok thak you. But which kind of CH341A SOIC8 SOP8 test clip with cable kit should I buy ? Do you have to recommend a particular store and a particular model of these devices, or can I buy them at random on Ebay?

@Rothwang

Zitat von lfb6 im Beitrag Bricked ASUS Z68-VGEN3 UBU microcode update

---

.... Those are low quailty items, so there might be always one in betweeen that's not OK. I bought one that got warm, didn't write first tries but afterwards worked perfectly fine. There's always some extra attention with being 100% sure that you read/ wrote what you intended to.

(If you need a soic 8 clip or a 1.8V adaptor depends on your hardware/ plans for the future...)

Something like:
https://www.aliexpress.com/item/32725360255.html
https://www.aliexpress.com/item/32789272774.html
https://www.aliexpress.com/item/4001347399521.html
https://www.amazon.com/KeeYees-SOIC8-EEP...r/dp/B07SHSL9X9
https://www.amazon.com/Organizer-EEPROM-...r/dp/B07V2M5MVH
https://www.amazon.com/Coomatec-Socket-A...e/dp/B08KG7YM45
......

---

Hi lfb6, I just bought the KeeYees model you recommended.

@ Lost_N_BIOS

<<Please link me to your BIOS download page>>

https://support.ts.fujitsu.com/IndexDown...C0-693926A9194E

Hi everyone. As you can see from the photos I bought the device you recommended, KeeYees SOP8 SOIC8 Test Clip, and I backed up the bios with the program downloaded from the manufacturer's website, CH341A Programmer v1.34:








then I tried with MMTool 4.50.0.23 to insert an NVME module, first the extended one and then the reduced one, but the program made me the same error messages as when I tried to modify the original Fujitsu bios.

So I tried again with UEFITool 0.28.0, following your guide:





but at this point, however, I do not know where to insert the NVME module:



Can anyone kindly help me?

If it is useful, this is the link to my saved bios:

https://www.dropbox.com/s/w82g3fqew6jn3o...upbios.bin?dl=0

- Recommend to connect the flasher not via USB- hub but directly to the PC

- Link to dump says 'file is uploading'

- What about:

Zitat von lfb6 im Beitrag #15

---

.....Since at least in the update files the FD is unlocked you could download Intel ME System Tools v9.1 from Intel Management Engine: Drivers, Firmware & System Tools
and try (*** according to DOS/WIN/WIN64/EFI version):
"FPT***.exe -i" => Post the complete output

"FPT***.exe -d spi.bin" , this would dump the complete bios, if that's an error try the following commands, they could give you the different regions of the bios chip:
"FPT***.exe -DESC -d fd_reg.bin"
"FPT***.exe -GBE -d gbe_reg.bin"
"FPT***.exe -ME -d me_reg.bin"
"FPT***.exe -BIOS -d bios_reg.bin"

Post the output and the resulting files.
...

---

https://www.dropbox.com/s/fm2y2059pm6eyj...ujitsu.Bin?dl=0

Zitat von lfb6 im Beitrag #21

---

- Recommend to connect the flasher not via USB- hub but directly to the PC

- Link to dump says 'file is uploading'

---

Zitat von lfb6 im Beitrag #21

---

- What about:

Zitat von lfb6 im Beitrag #15

---

.....Since at least in the update files the FD is unlocked you could download Intel ME System Tools v9.1 from Intel Management Engine: Drivers, Firmware & System Tools
and try (*** according to DOS/WIN/WIN64/EFI version):
"FPT***.exe -i" => Post the complete output

"FPT***.exe -d spi.bin" , this would dump the complete bios, if that's an error try the following commands, they could give you the different regions of the bios chip:
"FPT***.exe -DESC -d fd_reg.bin"
"FPT***.exe -GBE -d gbe_reg.bin"
"FPT***.exe -ME -d me_reg.bin"
"FPT***.exe -BIOS -d bios_reg.bin"

Post the output and the resulting files.
...

---

---

Zitat von lfb6 im Beitrag #15

---

.....Since at least in the update files the FD is unlocked you could download Intel ME System Tools v9.1 from Intel Management Engine: Drivers, Firmware & System Tools
and try (*** according to DOS/WIN/WIN64/EFI version):
"FPT***.exe -i" => Post the complete output

"FPT***.exe -d spi.bin" , this would dump the complete bios, if that's an error try the following commands, they could give you the different regions of the bios chip:
"FPT***.exe -DESC -d fd_reg.bin"
"FPT***.exe -GBE -d gbe_reg.bin"
"FPT***.exe -ME -d me_reg.bin"
"FPT***.exe -BIOS -d bios_reg.bin"

Post the output and the resulting files.
...

---

I downloaded the 9.1 version you recommended but it keeps giving me errors:

Those commands are supposed to be run on the corresponding Fujitsu system. Bios dump you posted does contain a ME 9.1 so those commands should work on such a machine.

That's a pity since you don't have a trustworthy bios dump to work with.

Ok. So what do you suggest me to do?

Zitat von Rothwang im Beitrag #25

---

I downloaded the 9.1 version you recommended but it keeps giving me errors:

---

Hi guys,

i have a fujitsu board d3222-A1 and i inserted the nvme driver to the bios rom file. but i cant get the bios back to the mainboard. if i use the dosflash with the updated rom file on the bootstick, it didnt take the new one. is there any other.

I've found something in the manual. but i dont know how to tell at the start do insert the .rom file.
ftp://ftp.kontron.com/Services/Software_...-Tool_HowTo.pdf

does anyone has an idea? or do I need a special programmer?

i've flashed the bios via afudos from ami to the bios. after the second change, the board does not startet anymore. 3 times beep sounds are repeating, the display is black and i cant do anything, to flash the original rom file back to the mainboard. anybody could help me?