I did it 3 times, first was using ASprogrammer u sent earlier and got some differences starting 00800700, then i used CH314A V 1.34 and there was mismatching then i erased and again used Asprogrammer now have 100% matching according to HXD. Will drain system as u instructed and wait for 2 minutes then restart unless you have other instructions?

Restarted and now it looks diiferent than before!!! Got back predator logo at startup now shall i restart, enter bios and apply defaults?

I dis actually restarted enterred bios applied defaults saved and restarted and got green logo and back to wrong info with ME as stated earlier is set to enabled but status temporary unavailable please see attached...


https://ufile.io/rlzprmkq


Have some updates, i unprotect, erased write verify and read and got 100% matching followed ur instructions in restarting entering bios restarting . Status of ME still as before but the difference is that i was able to install ME driver though still ME status in bios the same.

thxs

@KAL - If you can install ME drivers, then ME probably now working. Please run MEINFOWin -verbose and MEINFOwin -fwsts and post readout from both here (in spoiler tags)

Hey Man, they showed disabled kindly see attached

Please put in spoiler tags directly here so we can read easier, thanks

[spoiler][/spoiler]
 

@KAL - Please program in these two BIOS, then do the power drain thing between each, then check again. This is 100% Stock BIOS (1A and 10), maybe you have wrong BIOS region being used, not much else I can think to do.
If we can't get soon I'll have to Ask Plutomaniac to look at your ME FW, which I already know is fine due to taking it from known working programmer dumps from other users, so that will kinda be pointless to have him look too, so at a loss here
This way, with 100% stock BIOS test, you will loose serial etc for now, but ME FW should work, and we should be able to tell which BIOS is meant for this system, then we can go from there
Please test both, even if first one works, that way we can see if only one works properly, or if both work OK etc - then we;ll move forward again (update ME FW, unlock BIOS etc)
http://s000.tinyupload.com/index.php?fil...164622321420877

Before doing the above, please test this while you have unlocked BIOS. Go into BIOS, and find >> Me FW Image Re-Flash << Enable this, then reboot, then disable this, then from DOS >> FPTw.exe -greset
Then reboot and check MF FW status again, if still failing, test above BIOS set

Hey, Thxs for ur works...
Man just to clarify i cant start Dos even from usb bootable . my system is not compatibe and i even formatted the disk before and tried to boot from Dos to install it before windows and it did not work guess it is from bios not supported.


i tried to enable ME and restart then disable as u instructed but after i enabled it and restarting i found it is disableb!!

@KAL - You're welcome! Sorry this is seeming to be impossible fix!
You should be able to Shell, like Grub etc, since you can't boot to DOS. Do that, and use the Shell/EFI FPT instead. But really, if you do the full power drain properly, and long enough, the FPT greset is not needed, this power drain/wait does same thing.

ok will do it from shell...

You don't have to do it, as long as you remove all power, drain the board of all power, then wait 1+ minute, it's same/same if that is done instead.

ok proceeding with flashing 1A

1A booted normally similar 100% to the bios i had, bios advanced setting locked, wrong system info and green logo. ME was present with info below

@KAL - Yes, both of these are 100% Stock PH315-51 BIOS from Acer, all will be locked of course. What do you mean "Wrong System Info"? If you mean serial, this is expected, it's 100% stock BIOS without any edits. If you mean something else please explain.
Sounds like this is correct BIOS for your system then!

In regards to 10 - this may be RAID configured BIOS, not sure why it would do that with the HDD?
What do you mean about TPM? Are you using TPM? If yes, that is the main problem here all along probably! TPM should always be disabled and removed before any and all BIOS flashes, even dump and modify of your own BIOS

TPM is always available it dissappear when ME got disabled or not available and really had no idea about it being removed or something so how to remove it just turning it off in the bios is enough? And also yes wrong sys info meant wrong name, serial etc...

so now shall i turn off TPM in bios then flash back 1A or test3?
THXS

@KAL - When TPM is working, if dependent on ME FW working then when that is working too, yes, you can disable TPM in the BIOS. Yes, disable TPM before flashing or backup of BIOS, if you don't use TPM then you can disable always.
What do you see for sys info, should be generic or blank?

Yes, program back in the 1A I sent you at post #50, then enter BIOS, load optimized, save/reboot back to BIOS, make all changes you normally make and boot to windows.
Then shut down, dump the chip and send to me, I will then unlock menu and put in your correct system details.

didnt get what you asked, what do you mean by system info generic or blank? will do the flashing now after disabling TPM and will post the outcome...

You said system info (serial I assume), is wrong. I meant it should be 00 or FF (ie blank) or generic (0123456789 etc)
If not, and you see some actual random incorrect info, be 100% sure you are using Erase, then blank check, before you open BIOS file to write/verify, because the BIOS you are writing in is 100% stock, and those areas are blank or generic etc (ie no real data there)