Forum - RE: Intel Management Engine: Drivers, Firmware & System Tools

#1846 | RE: Intel Management Engine: Drivers, Firmware & System Tools datum

Mon Dec 14, 2015 2:15 am

Intel ME 6 Consumer 1.5MB Firmware v6.2.50.1062

Intel MEI Driver v5.2.0.1008 INF for manual installation (post #2, thank you elisw)

reply

#1847 | RE: Intel Management Engine: Drivers, Firmware & System Tools datum

Mon Dec 14, 2015 1:45 pm (Last edited: Mon Dec 14, 2015 11:49 pm)

Originally I said this:

Zitat von rootuser123 im Beitrag #1828
@plutomaniac I'm getting an error when trying to update ME Firmware. I've tried both DOS and WIndows versions. Here is the error: Error 8719 Firmware update cannot be initiated because Local Firmware Update is disabled.

My motherboard is the Gigabyte GA-Z170-HD3 on BIOS F5.

@plutomaniac I found the solution to my problem since I was impatient for Gigabyte to release an updated BIOS.

WARNING: DO NOT USE THIS METHOD UNLESS YOU WANT TO BRICK YOUR MOTHERBOARD. THANKS TO PLUTOMANIAC FOR THE CLARIFICATION.

This is what I did in cmd.exe in Windows 7 64-bit:
fptw64.exe -f NAMEOFMEFILE.BIN -ME

and in DOS:
fpt.exe -f NAMEOFMEFILE.BIN -ME

NOTE: You should shorten the filename for DOS as it has an 8 character limit.

You might like to write that in the intro post. It will ask if you want to continue and give you a warning that the byte size offset is not the same and just press Y on your keyboard and it will successfully flash it into the ME region. It reset my BIOS to default settings once I flashed the ME Region.

Thanks to @Fernando, @SoniX, @lordkag, @CodeRush and @plutomaniac for all the resources and help for modding BIOSes.

Current Desktop Configuration
Intel Core i9 9900KS @5.00GHz, Corsair Vengeance LPX 32GB DDR4-3600MHz Dual Channel, Gigabyte Z370 Aorus Gaming 5 Rev 1.0 Motherboard, Gigabyte Aorus RTX 2070 Super, Intel Optane M10 32gb NVMe SSD, Seagate FireCuda SSHD SATA3 2TB HDD @7200RPM, Enermax 850W Revolution 87+ PSU, Windows 7 Ultimate 64 Bit SP1

Secondary Server
Intel Xeon X5675 @4.60GHz, 16GB DDR3-1600 Triple Channel, Gigabyte GA-X58A-UD3R Rev 2.0 Motherboard, Gigabyte Radeon RX 470 4GB, Toshiba TLC 256GB SSD, WD Blue 3TB HDD, Antec HCG-900 900W PSU, Windows Server 2019

Current Laptop Configuration
Intel Core i7 4510U @ 2.00GHz, 12GB DDR3-1600 Dual Channel, Asus HM87 Motherboard, Intel HD Graphics 4400, NVIDIA GeForce 840M 2GB DDR3, Intel 535 SSD 360GB, Windows 10 Education

reply

#1848 | RE: Intel Management Engine: Drivers, Firmware & System Tools datum

Mon Dec 14, 2015 8:20 pm (Last edited: Mon Dec 14, 2015 8:26 pm)

Write what to the first post? That did not solve the BIOS-related issue. You just used FPT instead of FWUpdate and in a completely wrong way. What do I mean?

a) To reflash the ME region with FPT you need an unlocked Flash Descriptor which is locked under normal circumstances so FWUpdate is needed for most people.

b) You never flash the file that I give at the first post like that via FPT. FPT rewrites the whole ME region which means both CODE + DATA. The DATA are motherboard/OEM specific settings set via FIT/FITC. FWUpdate deals only with the CODE and not DATA. If you want to use FPT, you need to download the EXTR or RGN file I provide, change settings at FITC according to your own motherboard's ME firmware and then flash it. What you just did is flash the DATA section of whatever motherboard I extracted that firmware from. Especially for mobile systems this could easily lead to a brick. For desktop, since most OEMs use similar settings, it may not necessarily lead to a brick but instabilities, disabled options and so on. Whether it results in critical failure or just weirdness it doesn't matter. The proper practice is what I described above. For FWUpdate none of these are needed as any EXTR or RGN image with any DATA is good as long as the CODE integrity is proper.

c) That FPT warning is not normal and should not be ignored. The region you tried to flash is smaller than the actual SPI ME Region. If the SPI region had any data after the size of the new firmware you could have ended once again with a bricked system. Always make sure that the FIT/FITC modified ME region you are trying to flash has the same size by adding padding manually if they are not there to begin with. Otherwise you need to use -rewrite command to completely erase the previous contents of the SPI ME Region.

reply

#1849 | RE: Intel Management Engine: Drivers, Firmware & System Tools datum

Mon Dec 14, 2015 11:48 pm

Thanks for your clarifications plutomaniac, luckily I didn't brick my motherboard so I will delete my post to save other people's computers. So how would I extract the whole ME Firmware from my motherboard and use FITC to transfer the settings over to the latest ME Firmware so I can flash it with FPT since it flashes both DATA and Code?

Thanks to @Fernando, @SoniX, @lordkag, @CodeRush and @plutomaniac for all the resources and help for modding BIOSes.

Current Desktop Configuration
Intel Core i9 9900KS @5.00GHz, Corsair Vengeance LPX 32GB DDR4-3600MHz Dual Channel, Gigabyte Z370 Aorus Gaming 5 Rev 1.0 Motherboard, Gigabyte Aorus RTX 2070 Super, Intel Optane M10 32gb NVMe SSD, Seagate FireCuda SSHD SATA3 2TB HDD @7200RPM, Enermax 850W Revolution 87+ PSU, Windows 7 Ultimate 64 Bit SP1

Secondary Server
Intel Xeon X5675 @4.60GHz, 16GB DDR3-1600 Triple Channel, Gigabyte GA-X58A-UD3R Rev 2.0 Motherboard, Gigabyte Radeon RX 470 4GB, Toshiba TLC 256GB SSD, WD Blue 3TB HDD, Antec HCG-900 900W PSU, Windows Server 2019

Current Laptop Configuration
Intel Core i7 4510U @ 2.00GHz, 12GB DDR3-1600 Dual Channel, Asus HM87 Motherboard, Intel HD Graphics 4400, NVIDIA GeForce 840M 2GB DDR3, Intel 535 SSD 360GB, Windows 10 Education

reply

#1850 | RE: Intel Management Engine: Drivers, Firmware & System Tools datum

Tue Dec 15, 2015 12:03 am (Last edited: Tue Dec 15, 2015 12:04 am)

Hello guys.

Month ago I updated my ME Firmware to the latest 10.x version, before updating it I checked everything with MEInfo and MEManuf and etc, the older version that originally came with the laptop was also from 10.x branch, after the update to the latest version, I checked MEManuf and the test successfully passed.

But now something confused me, the latest 11.x branch has title - PCH - LP and my Intel chipset aswell has that notation, my question does 10.x the same notation or it is just the "Lynx Point" thingy ?

BTW, pictures of motherboard and ME from HWiNFO.

Best regards,
Andrej

acid96 has attached images to this post

1.PNG

2.PNG

reply

#1851 | RE: Intel Management Engine: Drivers, Firmware & System Tools datum

Tue Dec 15, 2015 12:37 am (Last edited: Tue Dec 15, 2015 12:40 am)

@ rootuser123:

Easiest way is to use UEFITool, extract ME Region. Two instances of FITC, one with extracted and another with the new downloaded and change settings to be the same. There is a good guide over at tweaktown, specifically here. Obviously, don't follow blindly, adjust according to your system and needs.

@ acid96:

ME 11.x firmware is for Skylake systems. LP stands for Low Power (U & Y cpus basically). The rule of thumb always applies: You can update only to the same major version you already have, 10.0 --> 10.0, 11.0 --> 11.0, 9.5 --> 9.5 etc. There are two exceptions shown at the first post but they are not Broadwell mobile (ME10.0) related.

reply

#1852 | RE: Intel Management Engine: Drivers, Firmware & System Tools datum

Tue Dec 15, 2015 11:28 am

Hello :)

Here is MEInfo Win32/64/EFI & FWUpdate EFI 11.0.0.1191

Pacman has attached files to this post

ME_tools_1191.zip

reply

#1853 | RE: Intel Management Engine: Drivers, Firmware & System Tools datum

Tue Dec 15, 2015 3:35 pm

Hi all, i'm trying to update MEI in my b150m mobo, but the file "Intel ME System Tools v11.0 r9" seems to be corrupted, it also happens to "Intel MEI Driver v11.0.0.1173 MEI-Only Installer", "Intel MEI Drivers & Software v11.0.0.1173 for Corporate systems complete package". Thanks in advance

reply

#1854 | RE: Intel Management Engine: Drivers, Firmware & System Tools datum

Tue Dec 15, 2015 4:17 pm (Last edited: Tue Dec 15, 2015 4:20 pm)

Intel ME System Tools v11.0 r10:

FWUpdate(Win): 11.0.0.1194
FWUpdate(Win64): 11.0.0.1194
FWUpdate(EFI64): 11.0.0.1191
MEInfo(EFI64): 11.0.0.1191
MEInfo(Windows): 11.0.0.1191
MEInfo(Windows64): 11.0.0.1191

@ paniwine:

Read the red text at the beginning of the thread on how to unpack. On the subject, can you do me a small favor? Run FWUpdate tool with the command FWUpdLcl64 -save ME.bin and attach me the resulting ME.bin file in an archive. You have a Corporate system and I'm looking for an UPD image from such systems.

reply

#1855 | RE: Intel Management Engine: Drivers, Firmware & System Tools datum

Tue Dec 15, 2015 7:10 pm (Last edited: Tue Dec 15, 2015 7:16 pm)

Excuse me for being stupid... I tried 7zip 9.xx and winrar 3.xx, I was confused because I could open some other files. I updated 7zip and now I can open the files, I'll uload the ME.bin ASAP.
DO you need any other information about my system?

paniwine has attached files to this post

ME.zip

reply

#1856 | RE: Intel Management Engine: Drivers, Firmware & System Tools datum

Fri Dec 18, 2015 10:29 pm

Intel ME 9.1 Corporate 5MB Firmware v9.1.37.1002

Intel ME System Tools v11.0 r11:

Flash Image Tool: 11.0.0.1191
Flash Programming Tool(DOS): 11.0.0.1191
Flash Programming Tool(EFI64): 11.0.0.1191
Flash Programming Tool(Windows): 11.0.0.1191
Flash Programming Tool(Windows64): 11.0.0.1191
FWUpdate(DOS): 11.0.0.1191
MEInfo(DOS): 11.0.0.1191
MEManuf(DOS): 11.0.0.1191
MEManuf(EFI64): 11.0.0.1191
MEManuf(Windows): 11.0.0.1191
MEManuf(Windows64): 11.0.0.1191
SPT Corporate FW Bring Up Guide 10/2015

@ paniwine:

Ah, I forgot to reply back. Thank you for the UPD image paniwine. If I happen to need something in the future and you are available I'll ask, I appreciate the offer.

reply

#1857 | RE: Intel Management Engine: Drivers, Firmware & System Tools datum

Sat Dec 19, 2015 10:06 am (Last edited: Sat Dec 19, 2015 10:12 am)

Hello,
sorry for my Question, but I've never done something like this before. I've just bought an older motherboard (MSI Z77A-GA45) with Z77 chipset. The newest Bios file is Version 2c from 29.09.2013 and has included an update for the ME firmware to version ME8.1.50.1456. But as I see here, it is NOT the latest one. Can I update it with your posted Version "Intel ME 8 Consumer 1.5MB Firmware v8.1.65.1586" without being afraid damaging my board? ME Analyzer tells me this: (see picture).

2nd Question: If I'm NOT updating ME Bios, because I'm to afraid, can I still use the newest ME Drivers "Intel MEI Drivers & Software v11.0.0.1173 for Consumer systems complete package" - or should I just use the simple ME driver (inf-file) without additional software?

Thank you in advance. With best regards, Bananenmann ;)

|addpics|3c0-1-03df.jpg|/addpics|

reply

#1858 | RE: Intel Management Engine: Drivers, Firmware & System Tools datum

Sat Dec 19, 2015 10:21 am

@ bananenmann:
Welcome at Win-RAID Forum!

Zitat von bananenmann im Beitrag #1863
Can I update it with your posted Version "Intel ME 8 Consumer 1.5MB Firmware v8.1.65.1586" without being afraid damaging my board?

Yes, you can update it and minimize the risk, if you follow plutomaniac's advices given within the start post.

Zitat
If I'm NOT updating ME Bios, because I'm to afraid, can I still use the newest ME Drivers "Intel MEI Drivers & Software v11.0.0.1173 for Consumer systems complete package" - or should I just use the simple ME driver (inf-file) without additional software?

I would prefer to install just the "pure" Intel ME driver.

Merry Christmas and a Happy New Year!
Dieter

My current System:
MB: ASRock X570 Pro4, CPU: AMD Ryzen 5 3600, System Drive: 500 GB Samsung 980 Pro, Graphics: Sapphire Radeon RX570, OS: Win10 x64 Pro
Donation Link:
If you are satisfied with my Forum activities, you can send a donation to my personal PayPal account by clicking onto >this< link.

reply

#1859 | RE: Intel Management Engine: Drivers, Firmware & System Tools datum

Sat Dec 19, 2015 11:03 am (Last edited: Sat Dec 19, 2015 11:05 am)

Hello Dieter,

Thanks for your welcome message and your help. I would follow the Instructions from Part C1: Identifying, Diagnosing & Updating Intel ME Firmware, while identifiing is not needed anymore, because I've done this already by analysing the downloaded newest, whole MSI-Bios-file (which incuded their latest ME firmware update) with ME Analyzer - as you've seen in my picture.

One last Question: I'm now using a very old Computer and with this Z77-MSI-Board and an Intel I5-3570 I wanted to build a (nearly) new one. Aftwerwards I wanted to update the whole MSI Bios (including ME8.1.50.1456), then installing Win10 x64 Pro, afterwards the MEI drivers v11.0.0.1172 (inf-file) - and at least update the ME firmware from here: v8.1.65.1586, as I told. Is this chronological order right?

Merry Christmas and a happy new year for all of you!!!
;)

reply

#1860 | RE: Intel Management Engine: Drivers, Firmware & System Tools datum

Sat Dec 19, 2015 11:22 am

@ bananenmann:
1. The ME Analyser tool checks the Intel ME Firmware of the BIOS, which is offered by the mainboard manufacturer, but not the Intel ME Firmware, which is currently within the mainboard's BIOS chip.
2. Your intended chronological order of the updates is ok

My current System:
MB: ASRock X570 Pro4, CPU: AMD Ryzen 5 3600, System Drive: 500 GB Samsung 980 Pro, Graphics: Sapphire Radeon RX570, OS: Win10 x64 Pro
Donation Link:
If you are satisfied with my Forum activities, you can send a donation to my personal PayPal account by clicking onto >this< link.

reply

Please enter a reason for warning.