hi lost n bios can you extract the microcode from a bios and put in the Toshiba bios 3.60 because I I found a bios from another laptop Toshiba but with diferent microcode can you do this? will send you the bios Toshiba 3.60 and the bios I wiil rename code extracted bios THANK YOU https://www.sendspace.com/file/wd8il6

@juanete - Yes, this can be done, but what microcode exactly do you need changed over, or updated? I do not need donor BIOS, only what BIOS you want edited, and tell me which microcode CPUID you want updated/changed to what version (or latest version)

the cpu id MICROCODE I want to update is 206A7 but UPDATED TO REV 14 BECAUSE NOW HAS 28 I think ,NOW I HAVE INSTALED I7 2860QM WITH THIS CPUID 206A7 AND I WANT TO CHANGE THE microcode version because the processor is wont go up than 2.7ghz when all core are on full speed at maxim and at maxim should be 3.3ghz all core I will ssend you the bios dump up with CH341A_130 program https://www.sendspace.com/file/cvt5c4 an if you can make another version with cupid 206a7 with Rev. 0x29 finily two bios with two diferent rev. one with rev 14 and another one with rev ox29 all two with cupid 206A7 THANK YOU

Will do tonight @juanete - you may need to do other mod (unlock MSR 194), you may also need updated ME FW, are you already using latest ME FW?

yes i remember that i use the latest me firmware and you did the modify with the me firmware to unlock the overcloking but with that firmware unlocked with overcloking wont boot the laptop on the page 20 we towlk about me frimware but with this unlock MSR 194 i dont remember if you make it what is that?thank you

I'll have to read back, maybe we need to update ME FW but not try to unlock it, just do the MSR 194 unlock

ok man you know better ,and by the adapter the original it was 90w 19v 3.95a and i have another that has 120w 19v 6a if requeres much power, i tried with 12ow adapter but the same results all core at maxim not more than 2.7ghz thank you

I think for now, aside from the microcodes you wanted to try, we leave ME FW as it is, and do the MSR 194 unlock and BIOS unlock. I don't think power adapter has anything to do with this
Here is three BIOS, all with MSR 194 unlocked, one with original microcodes you sent, and then one each w/ 206A7 14 and 29

http://s000.tinyupload.com/index.php?fil...656326903698842

You mentioned EC maybe controlling turbo before I remember, I just noticed setting in the BIOS that can be changed to disable that. You know about using grub and setup_var correct? If yes, see below for values to change (Or I can make visible for you in BIOS?)
EC Turbo Control Mode, Variable: 0x208[1] {05 09 08 02 01 9F 04 A0 04}
Option: Disabled, Value: 0x0 {09 09 4D 00 00 00 01 00 00}
Option: Enabled, Value: 0x1 {09 09 4E 00 01 00 00 00 00}

To disable
Setup_var 0x208[1] 0x0

To enable
Setup_var 0x208[1] 0x1

If you are not familiar with Grub and Setup_var, here is a guide I wrote for other use, but you should be able to learn how to use from reading the guide
See this page if your BIOS does not offer boot to EFI Shell on exit page - [Guide+Video] How to install windows on NVME SSD 960 EVO without clover on a board without NVMe support. (2)
Also, if that is the case, in each location make several copies of the file with different names, so at least one might be correct working name bootx64.efi, shellx64.efi, shell.efi

the ec turbo can be disabled from bios to disabled ,ok the results are the same with all bios not more than 2.7 ghz all cores, but when I test the cpu at maxim with intel xtreme utility the cpu goes to 2.7ghz and reach maxim at 41w not more I think the laptop is blocked somewere I will send you a fotos

Hello

With Skylake-X and Asus rampage VI Extreme, since the 4D microcode, the TJMax has gone up to 110° and the temperature of the cores is increased
Even passing TJMax at 105° (by default), cores temperatures are always increased (~ + 5°)

Does anyone have an idea of why ?

Thanks

Good you can see EC turbo! I only saw that in BIOS again and remembered you mentioned before, thought maybe disabled or enabled if currently disabled might help, since you thought maybe EC controlled CPU Turbo (Maybe that EC Turbo is something else)

So you think 40-41W limit set, that could be due to temps reach right then, or TDP limit set. Thanks for new images and info, I think we discussed this as possibility before.
I will enable those settings for you to see in BIOS, you currently cannot see them correct (TDP/TDC limits, temp limits, adjustments to all critical trip points etc)

yes I see these settings I will send you a fotos to see if these are the tdp settings but did you see in ona foto that I sendit to you that the programmable tdp tdp is supported but disabled?

Thanks for the images. In the first one, Thermal Config, there is some settings you do not see, one of them is CPU Temp read enable and CPU Energy read enable, maybe disable those could possibly help, especially the energy one?

Also, did you ever test all the available ICC profiles you can choose (Default is 4, from 0-7).

And did you test disable Advanced CPU Control >> Enable/Disable Energy Efficient P-State Feature - And disable Turbo PWR Limit MSR Lock (Default enabled), same page/section? Sorry, I thought I remembered TDC/TDP settings, but there is only these and the ones you have visible in thermal section
I think disable these two, or at least Turbo PWR Limit MSR Lock might work! @juanete Editing BIOS now, but had to stop so I don't end up double enabling something you already have enabled (might break BIOS) << DO you have these options, should be on same page as EC Turbo enable/disable?
@ Advanced >> Advanced CPU Control

For the SiSandra image info, I found that setting but there is only two options >> Configure the power saving modes associated with the processor.
[Dynamic Switch] The processor's power consumption and automatic clock speed switching functions are enabled.
[Always Low] The processor will always run at a lower level of power consumption and a low speed.

Dynamic CPU Frequency Mode, Variable: 0x215[1]
Option: Dynamic Switch, Value: 0x0 {09 09 39 00 00 00 01 00 00} << Default
Option: Always Low, Value: 0x1 {09 09 3A 00 01 00 00 00 00}

Did you leave EIST and C3 enabled for a test, then one more test with one each disabled and one enabled? One of those has to be enabled for Turbo to work, but I forget which

Give me some time, I will make BIOS for you with all these settings now mentioned visible.

* Edit 2
While we're checking to confirm, since I can't remember what we've enabled in the past and what's currently enabled in BIOS you are using now, please confirm all these settings, which you can see and which you cannot. I will make all these visible
Advanced >> Advanced CPU Control
Energy Efficient P-State Feature
Turbo PWR Limit MSR Lock

Power Management >>
Dynamic CPU Frequency Mode

These I already can see from your image above you cannot currently see
Advanced >> Thermal Config >>
CPU Temp read
CPU Energy read enable

I don't see icc profile 0.7 but I see all that you said all the function and I test some of them and not working the same result and when I test the energy efficient state with option disbled the laptop is lock on windows boot and I had to force to shut down the computer enter in bios again and enable again to boot normaly in windows,what I tried is I set long duration pwr limit to 99 ,long duration time windows to 56 and short duration limit to 99 and when pri plane current limit I set to lower the core frequency its go down but when I set o high value the processor wont work more than 2.7ghz and I think here is the problem Dynamic CPU Frequency Mode, Variable: 0x215[1]
Option: Dynamic Switch, Value: 0x0 {09 09 39 00 00 00 01 00 00} << Default
Option: Always Low, Value: 0x1 {09 09 3A 00 01 00 00 00 00} and in these number where is default yu could modify something?

ICC profiles should have optional choices 1 through 7 (1-7), correct? Looks like default is 4
These options you do not have visible, but rest I mentioned you already see? These are not visible in your image above, and I thought one could really help (Energy Read) CPU Temp read + CPU Energy read (Missing from your thermal config page)
I think disable CPU Energy read maybe could help, if that also disabled the sensor from using TDP/energy draw value, but I'm not sure, it may just stop it from showing values if monitoring software

And yes! That one you mentioned last >> Dynamic CPU Frequency Mode << This one is what SiSandra was giving you warning about. But no, nothing I can do there except make it worse (Set other options = "always low")
[Dynamic Switch] The processor's power consumption and automatic clock speed switching functions are enabled. (This is default/current enabled setting)
[Always Low] The processor will always run at a lower level of power consumption and a low speed. (Worse than now)

Those numbers only tell coding which you choose, it's not an adjustable thing only pick one option or the other. Ideally a third option should be there, disabled, but it's missing!
However, after some tinkering.... Yes!! I was able to make "Always Low" >> Disabled option instead! But, since it was not there by default, it may not work?


Let me check this in assembly and see if it looks like it will be disabled, then I will upload this test BIOS for you (And maybe 2-3 others, with other disabled values too in case this one fails)
Couldn't locate in Assembly, so could not compare and see layout of edit vs non-edit But, here's three BIOS to test all with Disabled set differently.

New setting "Dynamic CPU Frequency Mode" should now appear in "Power Management" menu. I did not change from default, so default will be set to Dynamic still
http://s000.tinyupload.com/index.php?fil...744669193592084