ok is fine .I will install the intel from intel page or the Toshiba site page because it has intel driver graphics too finile I put a socket on chip with bios to disamble the cip and rewrite the bios with programmer much easier ok thank you

@juanete - Best to get Intel driver from Toshiba page for your model since that would be the exact one that should work. So you want me to mod BIOS again, and set SG enabled instead of Auto, and enable IGD?
Here is that BIOS. if it fails, reprogram fullmenu2, then we try with only iGD enabled, then with only SG enabled.
https://www.sendspace.com/file/gnr14v

hi I tried and is not working thank you

What happens? What is not working, what are you trying to do etc? Show me device manager with display adapters expanded, it sounds like you only have one display enabled (NVidia). Please show me that with the BIOS I sent you last, with SG enabled (Doesn't matter for this) and iGD enabled (onboard GFX enabled, this we check now)
What CPU are you using?

Try connecting external monitor, sometimes this only way one of the graphics cards are used on some laptops. Test all external ports if you have more than one (VGA/DVI/HDMI etc).
Connect external monitor to this, boot to windows, is that screen showing image? If yes, then check GPU-z, is there two GFX options at bottom drop out, or only one in dropout menu?

is not working I will send you some fotos to see and the processor is i72860qm before it was i52410,i don't know I think the i7 is not fully supported by motherboard because I put an radiator with aluminium and the throttle still exists I think the bios is not updated for this i72860qm because some laptops with this i7 2860qm use 180w power supply,and this in the setup where it has turbo controlled by EC of bios has 90w 75w nad 65 w but does not have more than 90w could you modify the bios to accept full i7 2860qm?and here is a site with some bios and changes in all version but some versions of bios are missing on downloads https://support.toshiba.com/support/view...ntentId=3483311 thank you

Yes, looks like only Nvidia is enabled, or functioning. I don't think I asked already, before you changed CPU out, did the onboard graphics work?

I assume you can't confirm on another system the iGPU of this CPU is functional can you? TDP, power etc is not going to stop iGPU from functioning, it's possible vBIOS might though!
I don't know what you wanted me to see in the link you gave? Since ACPI is mentioned there, you can research, BIOS default is ACPI 3.0, but 4.0 is an option too, is that maybe needed for your CPU?

I can't change BIOS to higher power supply I see EC turbo control mode is disabled, but that is in CPU control settings so I don't think it's same EC you think of when mention EC FW?

This BIOS contains 4x vBIOS!
VBIOS in GUID 8DFAE5D4-B50E-4C10-96E6-F2C266CACBB6 >> SANDYBRIDGE-M - Intel(R)Sandybridge Mobile PCI Accelerated SVGA BIOS Build Number: 2104 PC 14.34 01/18/2011
VBIOS in GUID 0B2BF7F1-6BB4-48C1-98E2-131295CFDA03 >> E696 N12M-GE B01 VGA BIOS - Version 70.18.7F.00.14 Nvidia
VBIOS in GUID 93C5BEDB-AE4F-4070-B9E2-8CAF8D98162C >> E1076 SKU 0005 VGA BIOS - Version 70.08.54.00.0B Nvidia
VBIOS in GUID 4063F703-7849-4BC9-92FE-1940822FDA2F >> E1319 SKU 0010 VGA BIOS - Version 75.19.32.00.01 Nvidia

Soon I will post more test BIOS for you. With all same changes as last + Always enable PEG set to enabled instead of disabled (Still don't see how NVidia card work now with that disabled!?)
Also, second BIOS with all the same changes mentioned above + new vBIOS. If first one fails, do not use vBIOS one, I will redo vBIOS into previous one without the always enable PEG.
Nevermind, I think due to vBIOS size, it must stay at 2104 version, unless you have flash programmer to test other vBIOS and recovery with programmer if it fails.

* Pre-post Edit - I have made breakthrough I think, to enable these options I've been changing myself, that you couldn't see, I think I can make so you can choose option now!
Positing this now in case you're here waiting on reply, may take me another day or at least a few more hours tonight, to update these settings to be visible for you, and then add the vBIOS updates in other test BIOS too.

This setting I think I need to find, for SG to work properly, Advanced -> Video Configuration -> Pci Express Graphic -> PowerXpress Setting [Muxed Fixed Scheme]
I can see it in Unicode in the setup file, but can't get it showing in IFR or Intel tools Will keep on it, but maybe/hopefully it's only required in older/certain BIOS, or it's already default on that setting above!

*Edit - Here is quick test, just the following changes, new options visible to you I hope, test and let me know thanks!
Video Configuration >> Primary Display (Auto, IGFX, PEG, PCI, SG)
Internal Graphic Device >> New setting above RC6 >> Internal Graphics Device (Auto, Enable, Disable)
PCI Express Graphic >> Always Enable PEG (Enable. Disable)
https://www.sendspace.com/file/72oo72

@Fernando, can you please move all juanete and I's posts on this subject to it's own thread, thank you! I think it's too much going off topic in this thread for a long time, starting on page 14
And @juanete - this mainly for me to help keep track of everything too, probably better for you as well.

ok thank you ,in the older cpu i5 the internal graphic is not working ,the bios you send to me is 4.0? I will try the bios to see what happens thank you

No, the BIOS I sent just now is same one you've been using all the time, 3.60 I think.

ok now the primary display and the other options its showeed too, what changes I need make to working? ,I tried some combination but the results is black screen ,I tried with sg activated but the intel display driver wont install.i tried with bios without change anything but is not working what change I have to make?but to resolve problem with cpu can we update with bios 4.0?thankyou

So it worked? If yes, great!! Intel driver will only install once you see second device showing up in device manager display area (or in drop down GPU-z).
To me, this is what "Should" be working, but like I said above, I think we may need to find out how to change that one setting that I mentioned I can't yet (with the "Muxed" setting option)
Video Configuration >> Primary Display >> SG
Internal Graphic Device >> New setting above RC6 >> Internal Graphics Device >> Enabled
PCI Express Graphic >> Always Enable PEG (Enable. Disable) Either, since your NVidia card seems to work with it disabled or enabled?

I think I have to figure out how to change this setting for you from it's current default, whatever that is
Advanced -> Video Configuration -> Pci Express Graphic -> PowerXpress Setting [Muxed Fixed Scheme] << That is what needs set

There is BIOS 4.0?? Yes, we could have been using that all along, why haven't we? I don't know if that will resolve CPU problem, what is CPU problem? Sorry, I can't look back, we've talked too long across too many pages with other posts in this thread.
Update to that BIOS, and send me new dump

ok,when I set the settings on bios like you said the laptop is tryng to boot because the led is bliking but is not working, where I cant find the bios 4.0?the problem with the cpu is that the cpu is not corresponding with frequency it doesn't go at full speed with turbo boost ,only goes at 2.7ghz maximum ,and at lower speds goes on 3.5 or 3.2 ,the intel xtu overclocking detetct false turbo overcloking I will send you fotos thank you

Only you mentioned BIOS 4.0, not me, that is why I asked you "There is 4.0?"

As mentioned, I think we need to change this setting, which I can't figure out for you yet >> Advanced -> Video Configuration -> Pci Express Graphic -> PowerXpress Setting [Muxed Fixed Scheme] << That is what needs set (All in regards to the GPU's)

On the CPU, I really don't deal with all that, so please forgive me not understanding easily. I see "Non Max Turbo" is 25, does this need changed? Laptops have TDP and temp limits, which often override any other BIOS settings like turbo or other freq related things, and at full load that is likely hit fairly quickly.
Have you, or I, looked at and changed TDP and related settings yet? if not, this should be looked into. Do you have the Intel Tools Package? If not, please download it here, get V1.1 and open your BIOS in H20EZE_x86_WIN_100.00.02.13, go to "Other, setup menu, update default" and look through all those settings.
If you see any that you want to edit, change them, and hit patch on the bottom, then save BIOS and flash then test. If there is any you want me to make visible for you in BIOS, instead of you editing the BIOS, make a list and I will enable them for you if possible.
https://github.com/mikebdp2/Insider_BIOS_Tools/releases

ok if you can unlock the full processor much higher than x25 like x36 to make some test and the the option to overclocking the processor in extended icc are locked or to unlock the bios to work with the full speed of processor and with the internal graphic do you can make the power xprees visibile?or the laptop has anothers option who can be seen visibile ?thank you

Is default 25x? Yes, I checked, default speed is 25x for this CPU >>
Frequency - 2500 MHz
Maximum turbo frequency
3600 MHz (1 core)
3500 MHz (2 cores)
3400 MHz (3 or 4 cores)

I am still trying to figure out how to do the powerXpress setting, it's not shown to me like all the others, so I can't even find correct location to manually change in hex let alone enable visible to you, it is there though.

Do you have flash programmer, or can you unlock FD to write ME region of BIOS? ICC setting can be changed to default overclock profile in ME, but only if you can write to ME region freely. Any/all overclock would be limited to what I showed above for your CPU stock locked values.

yes a have the flash programmer if you mean the prograamer for bios that use CH341A SOFTWARE ,I don't know how to unlock the fd or the me firmware I don't have much knolege about this stuff , but the processor I know the default is x25 but the problem is the processor it seems to be blocked by the laptop with these limits like you said because only work at maxim 2.7 ghz when I strees the cpu on full load we nneed to unlock to work like he should work at 3.3 ghz on 4core when I stress the cpu .thank you for your help