@queirozfl - Maybe your NVME edit is bad? What do you mean "Didn't work", did the BIOS Boot?
If yes, then NVME edit should be fine if you put it into correct location, and you need to follow all steps exactly at step #4 in the "This is what you should do" section of this guide - [Guide] How to get full NVMe support for all Systems with an AMI UEFI BIOS
If you are not sure if your NVME insert was done correctly, send me your original dumped BIOS and I will do the edit for you

@Rabanik - Full BIOS would be only 16MB, not 16.7. Tell your friend to dump chip and give you contents, then I will put your BIOS region into it, otherwise you'll have to fix your LAN MAC ID later (if you have the ID now).
This can be fixed with FPT without issue later, provided you have the MAC ID
If you are OK with fixing MAC ID later, and it will be OK, I mean we can fix easily with FPT, it wont be blocked etc - here is full BIOS to program - http://s000.tinyupload.com/index.php?fil...980493813898144

It will take more than week when my friend receive my motherboard. He will dump the BIOS and I will send it to you. I do not want to play with LAN MAC ID later etc... Thank you a lot guys!

@Rabanik - If you know your MAC ID, maybe have images of the stickers on the board or from router etc, I can add it into the above BIOS now if you want.
But yes, if not, once your friend dumps BIOS and sends to you, I can then rebuild new BIOS with all your info in all the proper places

"But yes, if not, once your friend dumps BIOS and sends to you, I can then rebuild new BIOS with all your info in all the proper places "
I think that this way should be the best. I will wait for dumped BIOS. Thank you a lot for your willingness.

i'm trying to flash modded bios on my Z270 Prime AR with AFUwin and it redircets me to EZflash located in bios which gives me error "Update failed" with no other explanation
i tried both Recovery and capsule override but nothing changed
any idea?

hi
there is someone who has experience MSI NB ??
how to properly flash a custom file ,,from UBU updater

normally I only get a file error ./

gt75 7re "AMI 5" or AFUDOS is OK ?

Hi guys,
here is the dumbed BIOS from the flash chip. Could you modify it for NVME support please?
Thank you very much.

there is a mode to flashback bios with asus board?

@danyalbmw - That board has does not have USB Flashback, so you should use method I outline below.
AFU should not be required here, and you should NEVER use CAPSULE or RECOVERY with Mod BIOS, often = brick

@NeXt3R - Dump BIOS region with FPT (below), unlock BIOS/SMI Lock with this guide, then dump BIOS region again below (#1) and then mod that, then flash it back (Step #2 below)

@Lost_N_BIOS
Hi. Yes. But it was the BIOSREG. My friend needs a full size BIOS with LAN MAC ID etc. (everything)
The motheboard is in my friend's hands and yes he has the flash programmer. And that dump I have upload is the dump of the exact BIOS chip which you required.
Cold you arrange a full size modded BIOS?

Thank you very much.

Zitat

---

@NeXt3R - Dump BIOS region with FPT (below), unlock BIOS/SMI Lock with this guide, then dump BIOS region again below (#1) and then mod that, then flash it back (Step #2 below)

---

Thank you
I'll see "I still don't know if I need mod bios" old bios works still fine
.,,I have a hwprogramer "gpu TDP mod" planned so I'll try + test update my bios too
when the hwprogramer arrives for backup

thanks

edit,,translation

Zitat von Lost_N_BIOS im Beitrag #744

---

@danyalbmw - That board has does not have USB Flashback, so you should use method I outline below.
AFU should not be required here, and you should NEVER use CAPSULE or RECOVERY with Mod BIOS, often = brick

@NeXt3R - Dump BIOS region with FPT (below), unlock BIOS/SMI Lock with this guide, then dump BIOS region again below (#1) and then mod that, then flash it back (Step #2 below)

If you have already modified the BIOS in ANY way, you will need to re-flash it back to factory defaults using factory method (NOT FPT)!!!
Additionally, please remove all BIOS passwords, disable secure boot, and disable TPM or Encryption if you have enabled. Do this before moving on to below

If you do not have Intel ME drivers installed, install them now from your system driver download page, then start over here after reboot.
Check your BIOS' main page and see if ME FW version is shown. If not then > DOWNLOAD HWINFO64 HERE <

Once HWINFO is open, look at the large window on the left side, expand motherboard, and find the ME area.
Inside that section is the ME Firmware version. Take note of the version. (ie. write it down or get a screenshot)

Once you have that, go to the thread linked below, and in the section "C.2" find and download the matching ME System Tools Package for your system.
(ie if ME FW version = 10.x get V10 package, if 9.0-9.1 get V9.1 package, if 9.5 or above get V9.5 package etc)
> DOWNLOAD " ME System Tools " packages HERE <

Once downloaded, inside you will find Flash Programming Tool folder, and then inside that a Windows or Win/Win32 folder (NOT x64).
Highlight that Win/Win32 folder, then hold shift and press right click. Choose "open command window here" (Not power shell! >> * See Registry file below *).

If you get an error, reply to this post with a screenshot of it, OR write down the EXACT command entered and the EXACT error given.

((If "open command window here" does not appear, look for the "Simple Registry Edit" below...))

Step #1
Now you should be at the command prompt.
You are going to BACKUP the factory un-modified firmware, so type the following command:
Command: " FPTw.exe -bios -d biosreg.bin "

>> Attach the saved "biosreg.bin ", placed into a compressed ZIP/RAR file, to your next post!!! <<

Step #2
Right after you do that, try to write back the BIOS Region dump and see if you get any error(s).
Command: " FPTw.exe -bios -f biosreg.bin "
^^ This step is important! Don't forget! ^^

If you get an error, reply to this post with a screenshot of it, OR write down the EXACT command entered and the EXACT error given.

Here is a SIMPLE REGISTRY EDIT that adds "Open command window here as Administrator" to the right click menu, instead of Power Shell
Double-click downloaded file to install. Reboot after install may be required
> CLICK HERE TO DOWNLOAD CMD PROMPT REGISTRY ENTRY <

If the windows method above does NOT work for you...
Then you may have to copy all contents from the Flash Programming Tool \ DOS folder to the root of a Bootable USB disk and do the dump from DOS
( DOS command: " FPT.exe -bios -d biosreg.bin " )

@Rabanik - What is going on there? ^^ I made you NVME mod BIOS for this system already back in May - [Guide] How to flash a modded AMI UEFI BIOS (47)
Did you get flash programmer now?

@pipes80 - What is the model? If Intel, then yes, FPT as outlined above, if AMD see Asus section of post one, or ANNEX of this guide here (the one we're in now)

---

@Rabanik - Sure, no problem, I just wasn't sure what was going on there
http://s000.tinyupload.com/index.php?fil...616245598481332

@NeXt3R - OK? If you don't need mod BIOS, then nothing to flash, and no reason to make post about flashing mod BIOS

@pipes80 - For that board, see the "Annex" section of the first post in this thread
Dump BIOS that way, edit it, then flash back that same way

@Lost_N_BIOS
Thank you a lot! I will tell you if it works later for sure :-) but it will take maybe a month because I let to ship the motherboard with other things which are not finished yet.

I know the method but for a flashback no work because read only bios in region chip