@
Lost_N_BIOS 🤗🤗🤗🤗🤗
when you can i'll be waiting😬

C:\Users\Crow\Downloads\Compressed\WIN32>FPTw.exe -bios -f biosregm2f.bin
Intel (R) Flash Programming Tool Version: 14.0.36.1158
Copyright (C) 2005 - 2020, Intel Corporation. All rights reserved.

Reading HSFSTS register... Flash Descriptor: Valid

--- Flash Devices Found ---
ID:0xC84018 Size: 16384KB (131072Kb)

GbE Region does not exist.

Processing Flash memory block 35 from 3071.
- Erasing Flash Block [0x424000] - 100 percent complete.
- Programming Flash [0x0424000] 4KB of 4KB - 100 percent complete.
Processing Flash memory block 926 from 3071.
- Erasing Flash Block [0x79F000] - 100 percent complete.
- Programming Flash [0x079F000] 2092KB of 2092KB - 100 percent complete.
- Processed memory blocks 3071 from 3071.
RESULT: The data is identical.12288KB of 12288KB - 100 percent complete.

FPT Operation Successful.


C:\Users\Crow\Downloads\Compressed\WIN32>

thank you very much for saving my pc=)

@klangun - You're welcome! So, BIOS menu unlocked now, correct? If yes, thanks for the quick test and report back

@Alis1204 - You did not answer me about EC FW??

Bios menu unlocked now:) I confirm, thank you very much:) you are Gods gift

@klangun - Thanks, I appreciate the confirmation! You're welcome again, and thank you for the praise

@Lost_N_BIOS
only the bios do not flash the EC

@Alis1204 - Sorry for the delay!! Here, program this in - http://s000.tinyupload.com/index.php?fil...823915906719088
Remember >> For actual chip GD25B127 use software version 1.18 with chip ID GD25Q128, or ASProgrammer 1.40/1.41 using the GD25Q128C ID
After programming in, remove ALL power from the board for one full minute. This means remove main battery, PSU Cable, programmer clip, CMOS battery if possible, then press and hold the power on button for 10-15 seconds, then let board sit without any power for 1-2 full minutes
Then you can put back together and start system. Enter BIOS, load optimized defaults, save/apply, reboot back to BIOS and make any changes you need, then boot to windows. Then, do as requested below after this

After system running, please show me image of BIOS main page, and then dump BIOS region with FPT and send to me, so I can fix your system details.

@Lost_N_BIOS
Working 😊🙂😊🙂😊
thankssssss, the front LEDs do not work, and And I don't get sound even though I have the drivers installed, is there an option in the bios for the sound to see if it is deactivated or something?
another thing shortly I will tell you the whole story of this laptop since it gave an error that was only going to be solved with an unlocked bios

Biosreg.bin
https://mega.nz/file/rl5w0bQJ#k5pGkuft64...DPHQxghUqy_tHjI

@Alis1204 - Great to see it's running again now! Yes, I assumed there would be some issues, sorry I did not mention there may be issues other than missing details.
LEDs - This is maybe due to empty/sparse stock NVRAM, I did not put in your NVRAM because I was not sure if corrupted, and or what caused your brick initially. What caused the brick initially??
Or, the LED's may be due to you did not connect some ribbon cable, or tiny cable, correctly/fully. I would recheck all connections inside to be sure. Same applies to audio, generally audio and LED are not NVRAM issue, so I'm thinking this probably cable not connected correctly, or at all, best to double check.

Please resize that image to only 1000 px wide, or put it in a zip w/ max compression, thanks. Also, zip the .bin file, so put both image (resized or not) and.bin into single max compressed zip, thanks.
Sorry, I am on limited internet, so huge waste of time to download non-archived items like this for no reason when they could be put in archive.

You have unlocked BIOS now Hopefully that will solve your problem you mentioned

@Lost_N_BIOS
The original problem of this equipment was that it always gave bsod error, when I installed any operating system, it also froze when I connected the power adapter and I assumed it was some problem caused by the bios, so I asked him to unlock it to try deactivating Several options until I found the one that gives the error in general and it was the option "intel speedtest" that was the culprit of the failure of the laptop, I bought this laptop on ebay aware of the problem and the seller had about 7 units in that same state, I publish this for anyone who presents this problem has the solution of it; a special thanks to my almighty God who owns everything and then to @Lost_N_BIOS and the win-raid.com forum
Biosreg.rar
https://mega.nz/file/jopHnCxB#VHkVNKR8y2...aA6CuK1oNpyHA_Y
------------------

@Lost_N_BIOS

So, speedstep was causing BSOD, and freeze with power adapter too? All very odd, this setting should not cause either of those issues
Maybe reflash EC FW could fix this, but not sure, sounds like something is wrong/bad on the board with the power delivery components or the PSU block itself, or both.

Thanks, but I don't need to see image above. I need image of Main (resized to 1000 PX Wide, OR, put in zip with biosreg.bin) << I see you edited in link, thanks - Got the resized image now too, thanks

* Edit, do you have the 1.08 BIOS + EC FW package? If not, I will send to you, so you can reflash the EC FW to see if it fixes the speedstep setting issue.
I am also right now, making updated ME FW for you to flash in and writing out steps to do that. But, I have to run here in a minute, so wont post that info until tonight when I get back.

@Lost_N_BIOS, greetings again! I need your precious help again :) I just bricked my laptop by undervolting with invalid settings in bios. I already tried to clear cmos, remove battery, remove memory, remove drives. Nothing is helped: still have bootloop with black screen. I have original Tongfang GK7CP0 chassis flashed with last bios from XMG Neo 17 (XNE17M19), this bios was modified by you in june and was successfully flashed and running fine until now :(

Link to your modified bios: OverPowered TONGFANG CyberPower Machrevo MACHENIKE - Unlocked BIOS Guide W/ Files (20)

Here is link for original bios from XMG: https://download.schenker-tech.de/package/xmg_neo17xne17m19/ (EC and BIOS for XMG_NEO_M19_RTX2060)

What to do now? Do i need to buy programmer and flash something magic to spi on motherboard? The only hope is your help 😇

Here is spi photo from my motherboard:

@Lost_N_BIOS hey, i dont know if u could help me, about, i change the prochot from 95C to 100C but when i boot in windows it keep chaging for 95C do u have some idea about what is changing it?

edit: i found have a setting in throttlestop that changes it to 100C again so it keeps now in 100C as default by intel. thanks anyway

@KORD_12.7 - Since you cannot clear CMOS, you will need flash programmer setup (CH341A + SOIC8 / SOP8 test clip with cable)
Here is guide on how to use - [GUIDE] Flash BIOS with CH341A programmer
And here is software package - http://s000.tinyupload.com/index.php?fil...213094641136166
If you need links to example programmer/clip or bundles, let me know.

For W25Q128JV - Use ASProgrammer 1.40/1.41 (OK read/write) or Colibri ver. 1.0.1.62 confirmed read/write OK (use BV ID)

Once you get the programmer, dump current BIOS (Read >> Verify >> Save) then send me the file and wait, I will make you BIOS to program back

@Lonely wolf - Maybe some software in windows was changing it back to 95C? When you set 100C in BIOS, and reboot back to BIOS, was it still 100C? If yes, then something on windows side causing that
Nice you found solution

@Lost_N_BIOS - in local electronic store i have seen this programmer setup, like on picture below:



Is it enough for my purposes? Can i buy and use it?

UPDATE
Just checked "[GUIDE] Flash BIOS with CH341A programmer", looks like it's exactly what i need. Thanks for info.