@Lost_N_BIOS
Here, I've got them both in a .rar for you.

http://s000.tinyupload.com/?file_id=71133432399404513634

Thank you again.

I touch de Offset Voltage, I have de Bios and the Nvram data, But the laptop Turn on and off. I have the CH341a and the sofware

@wsjbw - So you set voltage too low? If yes, do you have dump of your BIOS from before this happened, like original FPT or AFU BIOS region dump? If yes, send to me, along with your current dumped BIOS from programmer.

@Alwaysasbefore - Thanks, I will check it and get back to you shortly

Sure, Please bro, I'm crying...

@wsjbw - What is your BIOS Chip ID? IN case I need to have you make a new dump, and or so I can tell you which software/version or chip ID to use to write back so write does not fail.
Sorry, I thought you posted it before. I also need dump of your current BIOS chip contents. Before you dump it, answer me the above BIOS chip ID question, so I can tell you what software/version to use etc.

The bios Chip: Windbond (W25Q128FV)
the Nvram ( GIGA DEVICE/ GD25Q20)

@Alwaysasbefore - I see the issue! You put setup into AMITSE, so you need to rebuild your mod BIOS properly is all
I can't check your actual menu modifications, since there is no AMITSE here to check, so as long as you did the edit OK then all you need to do is replace the modules into proper location.
General note, only replace same way you extracted (As-Is or Body), just general comment there, I did not look at this. Then pay close attention what you are replacing into where. Setup into setup only, and AMITSE into AMITSE only

@wsjbw - For W25Q128FV use Colibri (included below) or ASProgrammer, make a dump and send to me
http://s000.tinyupload.com/index.php?fil...213094641136166

@Lost_N_BIOS Thank you so much for the help. I needed to have set my file type to "all" when viewing the folder through file browser. I didn't see the .efi file originally. Fixed it!
Will be sending you a PM promptly.

Hello!

Thanks for your help @Lost_N_BIOS successfully modded my bios using your guide, and best of all no more damn speed step! Thanks again!

@Alwaysasbefore - You're welcome! Actually, it should show you the correct type visible, usually. If you are replacing body of PE32 it should show .efi/.dxe/.bin/.pei by default, and if you are replacing As-Is it should show .sct/.bin by default.
I see your PM and replied, thanks! If you need help to do the mod, let me know! Otherwise, let me hear of your success and BIOS accessibility once you redo and reflash your mod BIOS again

@wsjbw - Uhh-ohh, I see file named Empty, if it's blank/empty (00 or FF) then that is a bad dump and you'll have to try again. I will check it and reply again soon, or edit this post with file back for you etc
*Edit - Yes, EMPY BIOS.BIN is blank file (all FF), this is bad dump. Try again, probably clip was not on perfectly, or you need to leave in main battery or PSU cable possibly (or remove one or both etc)
BIOS stock.bin is also a bad dump, what is this anyway??

I need a proper dump of your current BIOS contents, and then ANY previous BIOS backup from BEFORE the BIOS bricked
^^ This "previous backup" can be FPT dump, AFU Dump, programmer dump etc, does not matter, I assume you MUST have this, since you had to dump BIOS in some way previously to make a mod BIOS.

You should send them email request for BIOS package for your Mech 17 GK7CP6S 1660ti - I think they send out BIOS packages via email for the models they don't have BIOS linked on site

@Vic20 - You're welcome! Great to hear all is well and things went smoothly again for you!

The flash worked great! I really needed to get after my Fan Speed settings. Seems like some software made all of the temperature thresholds wrong, so being able to fix that was exactly what I needed.

@Alwaysasbefore - Great to hear all is working better this time around!

Hey, I have an Evoo LP5 (EG-LP5-BK) that I would like to unlock the bios. I followed the section called "Dump BIOS Region w/ FPT" and attached a copy of my bios dump below. I removed all bios passwords and I disabled secure boot before dumping. After I write back the bios region dump with "FPTw.exe -bios -d biosreg.bin", the only error I got was "GbE Region does not exist." Otherwise it says "RESULT: The data is identical.10240KB of 10240KB - 100 percent complete. FPT Operation Successful" Thank you for any help you can give me, I really appreciate it.

@cylencer - Thanks for doing all the right stuff up front
Here is your unlocked BIOS, flash it back via >> FPTw.exe -bios -f biosregm.bin
https://ufile.io/luxi3rbu

*** WARNING - To ANYONE with laptop and unlocked BIOS!!!! ***
DO NOT try to enable this graphics card or disable that card, switch cards etc. Otherwise you will end up with no display output (ie black screen) and no way to recover except by blind flash or with flash programmer.
You can change graphics related settings, like changing memory sizes, or core speeds etc, just don't try to disable one card or change which is main etc.
Additionally, be very careful when trying to undervolt CPU, you can leave BIOS unbootable due to CPU voltage too low (Sometimes even 0.05 is too much)

*** WARNING *** - This BIOS is user specific! If you are not user cylencer at Win-RAID.com forum, DO NOT USE THIS BIOS!!
If you do, and you are not cylencer, then you will loose your serial, UUID, OG NVRAM, and possibly LAN MAC ID as well.
You have been warned!!!