Zitat von Lost_N_BIOS im Beitrag #269

---

Use 1.30 or Colibri then. BV ID mainly needed for proper writes with 1.30 or 1.34, but best to just always use with that software (FV read may be OK, but not ideal, write will fail unless you use BV ID)
For colibri, you can use FV ID. Try without power/battery first, then if you can't detect chip, connect main battery, then if still no, connect PSU cable, then if still no, remove main battery and have PSU cable only.

---

Hi there,
I am having problem to flash winbond 25Q40EW, when i am using the ch341 (black version with 3.3v mod) with the 1.8v adapter it wont detect the chip but when I try it without the adapter it detect the chip but won't write to it :'(

PS : this is my second chip and second 1.8v adapter that I ordered thinking that it might be the 1.8v adapter that is faulty but it was not the case

since there is no answer I decide to change the chip to winbond W25X40CL and succesfully flash the chip and get my video card back up and running

Hi @Lost_N_BIOS

I solved problem. Its me region that i think. I injected clean me region v.9.5.52.1940 and pc runnig.

But i can not found same version of me driver.

My pc nxp proximty sensor nfc not working. Because of this i think.

Can you help me please?

Hi everyone, new here, I just corrupted the bios of my motherboard, a Gigabyte Z87x. I would like to know if I can use this method to flash the bios again without removing the motherboard from the case by just unplugging the power cable? Thanks to all of you

greetings @Lost_N_BIOS

my first post and my first time working with this programmer/software so please excuse if i am misunderstanding. but i believe i dumped the bios correctly, can you make me a clean file to flash on the board to remove password? thanks for your time and assistance!!

I have HP 4300 SFF PC. Is it possible to mod the bios of its motherboard with custom rom ( having Nvme drivers) and make Kingston A2000 bootable with windows 10 in it. Please reply I want to upgrade my 50+ HP 4300 PCs.

Greetings All,
I hope to be in the right place, otherwise I regret for any trouble this could case.
My goal is to flash a new boot loader on a router. Soldered chip is EN25Q64, I bought CH341A programmer (actually, two of them) and I'm not able to detect chip with many different versions CH341A Programmer (1.18 to 1.29) and different softwares (AsProgrammer).
I also tried using wiring on board lateral pins in addition to normal adapter.
I run on Win10 but I also tried on debian (flashrom).
Is there something popping in someonelse mind?
Thanks

UPDATE 9th Jan
Probable problem found: damaged Pomona 5252

Zitat von phoenix60 im Beitrag #277

---

UPDATE 9th Jan
Probable problem found: damaged Pomona 5252

---

Brilliant, got me out of a hole - flashrom magic -thanks

I'm trying to hack HP's Sure Start mechanism. It claims to store 2 copies of the BIOS in the system flash and also the BIOS controller firmware. Would this be able to modify both the original BIOS and its backup? I believe that once this is done, it'll be open season on HP computers for BIOS modding.

Hi there,
I have the following question about the CH341A programmer.
If I attach the SOIC8 clip (adapter) to the BIOS chip (soldered chip), can a short circuit occur, e.g. if the clip is not seated correctly, is crooked and PIN 8 and 7 are connected?
I know the red cable at PIN 1.
Thanks very much.

Hi,
does anyone have experience with the SOIC8 clip from the CH341A?
I have a soldered chip and have to use the SOIC8 clip. I bought a loose chip to test it out. However, the PINs of the chip are bent by the SOIC8 clip. The SOIC8 clip is very strong. My question: If I now attach the SOIC8 clip to the motherboard, can the PINs bend or even tear out of the soldered connection?

Gonna Try it

msi b550 MX25U25673G

using latest Asprogrammer, using the search it will list the chip. other older software wont
reading it with battery off it only gives me FFFF and with the battery in I get 0000

where do I go from here? anyone

Brilliant tutorial, thank you for this.