@Lost_N_BIOS

I did a backup with AFUDOS from your flashed bios. In UBU i got this (looks great) :



I will restore later the original bios (without capsule) and dump it with the programmer but first I need to set up the G703VI.

Just for info i found this : HWiNFO and Microcode and I don't know where to check in there to much options even in AIDA64

Animated logo is not a matter got all options to disable them in bios and sound too. I discovered I see Intel logo at boot only when CSM is enabled.

For the G03VI (APTIO V) the best is to give you the dump from the programmer ?

@Svan - looks good then, that all looks like exact edits I did for you!

Here's the three places where you see current "in-use" microcode with AIDA64 and HWINFO64 (two places, one in small CPU-z like window and one in the large AIDA64-like window)


For the G03VI is this AMD or Intel CPU system? Anyway, yes, go ahead and lets dump, that way you get familiar with using that, how it works on your system, and so you can find which version software works with that system too.
That way if recovery is needed then you have a valid backup already made and know what works and how etc

@Lost_N_BIOS

Hi, here is the pictures I got in HWINFO got 27h in AIDA64 :



Will try the dump today. Cheers.

@Svan - Great, then it's as it looked, mod BIOS flashed in fully and is working fine
Start a thread for your other system, about the dump, and put all the details there especially chip ID, and I'll try to help you on it.
In regard to your 1, 2, 3 choices in PM, I forgot to reply. You can often just dump BIOS region via FPT and edit then reflash too, if it's an Intel system.

Zitat von Lost_N_BIOS im Beitrag #19

---

mod BIOS flashed in fully and is working fine

---

My FIT button is disable im using uefi tool ne alpha 51 any suggestion ?

@Sober - if FIT tab is grayed out, then there is no FIT table in your BIOS.

Hi guys! Help add microcode 406c4 to the HP 15-ac BIOS.

I tried it myself, it doesn’t work ...
https://ftp.hp.com/pub/softpaq/sp96501-97000/sp96831.exe
BIOS id 080C6

@Keep3r88 - 406C4 is added to the BIOS in your attached image above, not sure what you mean you can't? What doesn't work?
I didn't check the file, since your image shows it's already added.

Firmware added by h20eze. Perhaps the bios is not correctly assembled. caps lock flashes 1 time with it. processor installed new sr2kl

H20EZE breaks BIOS usually for something like that (CRC32 checksum usually). How are you flashing BIOS? I can do mod properly for you, but need to know how you are flashing first.

@Lost_N_BIOS thanks for the help!
I use the programmer tl866ii.

I tested several options for modifications, they do not work ... There are no ideas.
decrypted official bios.

@Keep3r88 - send me programmer dumped BIOS and I will update the microcodes for you
Before you know it's the mods that are failing, and not your write process, please dump BIOS, erase chip, blank check, and then program the BIOS back and ensure that it works.
This way you know your write process is working with programmer, then if edit BIOS fails you know it's the BIOS edit not the programming of the BIOS with programmer.

Zitat von Lost_N_BIOS im Beitrag #29

---

@Keep3r88 - send me programmer dumped BIOS and I will update the microcodes for you
Before you know it's the mods that are failing, and not your write process, please dump BIOS, erase chip, blank check, and then program the BIOS back and ensure that it works.
This way you know your write process is working with programmer, then if edit BIOS fails you know it's the BIOS edit not the programming of the BIOS with programmer.

---