Probably not related to the mod. Can u get into safe mode?

I didn't try to go into safe mode. I can try.

But when I go back to the original BIOS + the i3 7100 works normally.

Zitat von Lost_N_BIOS im Beitrag #794

---

@life23vn - You need to have flash programmer (like CH341A + U Type Flat IC Extractor - chip puller), or do pinmod (See "E.1", then section B spoiler #2, image 1-2) to unlock FD, before you can use Coffee CPU

---

@life23vn - If your mod BIOS contains different FD or ME (compare both regions in hex) than original BIOS contents then No, if not then possibly Yes. What is your current ME FW version, and what version is in your mod BIOS?
If you do not have flash programmer, order one + BIOS extractor or SOIC8 clip+Cable if BIOS soldered to board, then wait until it arrives, otherwise if BIOS = brick and wont work with your old CPU then you will be out of luck and have to wait until programmer arrives.

Somebody could show me the method to connect 2 Pin CPU: material, glue, ...
Thank so much

Get that type of paint that is used to repair broken defroster stripes in car windows. Apply with a tooth pick.

So after some trial and error got the bios flashed on the Maximus 9 extream, swapped in the 9700k and it didn't even try and boot. Will need Todo pin mod. I have some solder paste on the way and kapton tape as well. Also needed more fittings for water cooling so it worked out.
https://www.amazon.com/dp/B009KB67ZC/ref...i_dlhCEb7P2AD1Y

https://www.amazon.com/dp/B0195V1QEI/ref...i_rnhCEbNJ0S3TP

Are these products good for what I need or should I look into something else?

@TechNaOkami - You may be able to find info in Google for SKTOCC mod for that board, especially if you can find a boardview file or schematic (Boardview would be better).
Then you wouldn't need to connect pins on the CPU. Maybe @chinobino @Svarmod @Revlaay @_haru have image or link for you?

On the kapton tape, that's personal preference, you may have better luck with thinner width, cutting to size in strips, vs trying to cut out of huge width tape, plus is cheaper to get less wide tape.
For the pin connect, if you don't want to do with solder iron or solder and hot air, that paste will work but you can probably also find smaller amount of that too. If you were going to hot air that into place, you can do same with regular solder (practice on something dead, you will see it's easy to do)
But really, best to do the SKTOCC mod to the board so you don't have to mod the CPU, or use defroster tape repair kit (conductive epoxy), or copper tap, as mentioned above, like this - https://www.amazon.com/Conductive-Copper...s/dp/B0827QM8GD

Whats SKTOCC? ive been combing through the forum but haven't seen it much till i started googling it.

I'm new here on the forum and I tried to modify the Gigabyte Bios ga-h110m-h to use the i3 9100f, but an error appears in the middle of the procedure.

"Ready Update GOP & VBIOS...
VBIOS ver:File can't be opened.
error happen..."

When this error appears, the BPM.exe program opens and the following error message appears:

"Line 249 (File '...\2019.1229\Coffee_Lake_Mod_Tool_\bin\ssf.exe)
Error: Array variable has incorrect number of subscripts or subscript dimension range exceeded"

This is what appears in the program 'Allinone.exe':

Zitat

---

????????????????????????????????

acknowledgement
CodeRush: UEFITool and other tool author
Fernando: Win-Raid owner
SoniX: UBU tool author
platomav: ME Analyzer
Mov AX, 0xDEAD: PCIE patcher
s.napi: Fixing HT
dsanke: many research info

????????????????????????????????

Process file "D:\Downloads (D)\mb_bios_ga-h110m-h_f23\H110MH.F23"
Choose Target CPU :

B0:
G49x0(T),G5420(SR3YH),G55x0(T),G56x0(T),8100(T),8300(T),8350K,
9100(T),9100F(SRF7W),9300(T),9350(K,F)

U0:
G54x0(T),8400(T),8500(T),8600(K),8700(T,K),8086K,
9100F(SRF6N),9400(SR3X5),9400F(SRF6M),9500,9500F(SRF6Q),9600

P0:
9400(SRELV),9400F(SRFAH),9600K(SRELU),9600KF(SRFAD),
9700KF(SRFAC),9700K(SRELT)

R0:
9400(SRG0Y),9400F(SRG0Z),9500F(SRG10),9600K(SRG11),
9600KF(SRG12),9700(SRG13),9700F(SRG14),9700K(SRG15),9700KF(SRG16)

?B0:1? ?U0:2? ?P0:3? ?R0:4? ???:5? ???: 1
================================================================
brand: Gigabyte
Mainboard: H110M-H-CF
Version:F23
================================================================
ME Version of BIOS is 11.8.50.3425
ME TYPE of BIOS is Consumer
Chipest H110
Replace ME Version to 11.7.0.1229
Done!
================================================================
Ready Update GOP & VBIOS...
VBIOS ver:File can't be opened.
error happen...
Press any key to continue. . .
================================================================
Enalbe CPU PCIE ...
[total hits/matching patterns/non-matching patterns]
[004/1/0] bios.tmp.patched
1 files checked, 1 changed.
\CoffeeLake was unexpected at this point.
================================================================
Ready to Insert CPU MicroCode...
Insert into Vol[67ABC]: 03
Done!
????????????????????????????????

Congratulations
>>: "D:\Downloads (D)\mb_bios_ga-h110m-h_f23\Gigabyte_H110M-H-CF_F23.CON117.67ABC.bin"
JOB Done
Press any key to exit

---

I tried to use the F23 and F24 versions of the Gigabyte bios. Attempts were made using the program in the folder "2019.2229" and "update.618".

I hope someone can help me, I thank you for your attention.

Update:

I was able to do the whole procedure without problems, after moving the files from the folder "2019.1229" to the folder where the F24 bios is located.

Below is the log for "Allinone.exe":

Zitat

---

????????????????????????????????

acknowledgement
CodeRush: UEFITool and other tool author
Fernando: Win-Raid owner
SoniX: UBU tool author
platomav: ME Analyzer
Mov AX, 0xDEAD: PCIE patcher
s.napi: Fixing HT
dsanke: many research info

????????????????????????????????

Process file "D:\Downloads (D)\mb_bios_ga-h110m-h_f24\H110MH.F24"
Choose Target CPU :

B0:
G49x0(T),G5420(SR3YH),G55x0(T),G56x0(T),8100(T),8300(T),8350K,
9100(T),9100F(SRF7W),9300(T),9350(K,F)

U0:
G54x0(T),8400(T),8500(T),8600(K),8700(T,K),8086K,
9100F(SRF6N),9400(SR3X5),9400F(SRF6M),9500,9500F(SRF6Q),9600

P0:
9400(SRELV),9400F(SRFAH),9600K(SRELU),9600KF(SRFAD),
9700KF(SRFAC),9700K(SRELT)

R0:
9400(SRG0Y),9400F(SRG0Z),9500F(SRG10),9600K(SRG11),
9600KF(SRG12),9700(SRG13),9700F(SRG14),9700K(SRG15),9700KF(SRG16)

?B0:1? ?U0:2? ?P0:3? ?R0:4? ???:5? ???: 1
================================================================
brand: Gigabyte
Mainboard: H110M-H-CF
Version:F24
================================================================
ME Version of BIOS is 11.8.50.3425
ME TYPE of BIOS is Consumer
Chipest H110
Replace ME Version to 11.7.0.1229
Done!
================================================================
Ready Update GOP & VBIOS...
VBIOS ver:1046
Updating vbios...
\mb_bios_ga-h110m-h_f24\tmp\878AC2CC-5343-46F2-B563-51F89DAF56BA\body.bin') was unexpected at this point.
================================================================
Enalbe CPU PCIE ...
[total hits/matching patterns/non-matching patterns]
[004/1/0] bios.tmp.patched
1 files checked, 1 changed.
\mb_bios_ga-h110m-h_f24\worktmp\Gigabyte_H110M-H-CF_F24.CON117.PCIE.CAP was unexpected at this point.
================================================================
Ready to Insert CPU MicroCode...
Insert into Vol[67ABC]: 03
Done!
????????????????????????????????

Congratulations
>>: "D:\Downloads (D)\mb_bios_ga-h110m-h_f24\Gigabyte_H110M-H-CF_F24.CON117.67ABC.bin"
JOB Done
Press any key to exit

---

A doubt. After this procedure will the bios still support Kaby Lake or Sky Lake?

thank you

finally msi b250m pro + 9400f U0 succesfully boot and work 100%

Thank you again
With this tool succes boot with i5 9600k (still using msi b250m pro vh)

Hey guys, I just used the tool for my maximus gene VIII board with the asus flashback feature. I just renamed the bin file to m8g.cap and flashed it. The blue led blinked for around 3 minutes & the computer shut off but the led was still on when it turned off, I don't know if it was succesful or not. I want to flash the bios before I buy a cpu, how can I check if the bios was updated? Also can I use liquid metal for connecting the cpu pins? I have liquid metal from my skylake delid at home. Thanks in advance.

Thank, it's work with Asrock Z270 Extreme 4. (Need E6 method of plutomaniac's [Guide] Unlock Intel Flash Descriptor Read/Write Access Permissions for SPI Servicing before Flash bios)
"setup_var 0x68F 0x01" for who don't have time.