Hi @Irgen

I am late to the party here and new to this forum, but have the exact same issues with the exact same processors (QL2K) and board re #322. Firstly, apologies if I am not observing correct forum etiquette with this reply (ignorance is my excuse).

My on-board Power LED remains RED constantly, no pins are bent and it does not seem to matter whether it is single or dual configuration.

My question to you is did you establish whether this was a board or ES chip issue (QL2K is simply not going to work on this board)?

@Lost_N_BIOS, copying you in for info, since it may look like the QL2K simply can't work on this board. Would defy probability that @Irgen and I have the same issues with board, should board be faulty, while the chips appear the same and the ebay seller you guys were discussing indicated his bios mod would not work specifically with this chip.

Your BIOS mod flashed fine and I assume to be working perfectly per the large number of positive response to this. Since the flash utility is working on-board, this makes me lean towards the QL2K being the issue?

Thanks in advance for any help/advice you guys can give.

@Lost_N_BIOS

Is this forum also providing BIOS for Pro WS C621-64L SAGE single CPU Motherboard ?

Zitat von Xeon_Loving_Quant im Beitrag #527

---

My question to you is did you establish whether this was a board or ES chip issue (QL2K is simply not going to work on this board)?

---

Thank you so much for the quick response. That's what I thought would be the outcome.

You roll the dice, you lose sometimes.

The comments within this thread have been invaluable though, generally, so maybe not a complete loss on this little gamble. :)

Does anyone tried this mod with newer Xeon Platinum 82XX ES Btw? Seen some of those on Ebay.

Hello
I bought a Xeon Platinum 8124M SR37R with cpu id 50653 and didnt work on c621 cage with any bios in this thread.please help me,thanks

Zitat von Irgen im Beitrag #531

---

Does anyone tried this mod with newer Xeon Platinum 82XX ES Btw? Seen some of those on Ebay.

---

Zitat von TRoy1990 im Beitrag #532

---

Hello
I bought a Xeon Platinum 8124M SR37R with cpu id 50653 and didnt work on c621 cage with any bios in this thread.please help me,thanks

---

Hi, there.

I'm a novice to modify BIOS.
I have a gigabyte c621-sd8 board and two ql1ls, I have read all these posts.
I followed Lost's explanations about asus c621e sage.
I extracted microcode from mod asus c621e sage bios (5503)

Zitat

---

#241

---

.
gigabyte c621-sd8 bios(F7) are modified with recent UBU tool and above extracted microcode.
CH341A programmer is used for rom flashing.

the result is perfectly working. thanks everyone in this post.
debian buster is installed in this mod bios machine.
legacy booting was failed by edd=off and OS writing problem, but UEFI booting is successful.

I couldn't link my mod, because I'm a new member. I have to make 3 posts, ~~;
[img][/img]

Zitat von levelud im Beitrag #498

---

@Morockin Thanks for the guide, I have used all your settings, but I still stuck on 2.2GHz Allcore, is there perhaps picture 1 missing? Perhaps you did also unlock something in Digi+ Power Control?

---

Hi
I have 2 Xeon Platinum 8124M QS QMQ1 CPUID 050654h.
New motherboard "Asus W621E Sage" never used, I insert bios 6201 modified via flashback. "All Ok flashed"
I install Cpus and waterblocks
As soon as I turn on the power supply, the motherboard starts up without clicking any buttons and gives me error 00
QMQ1 is not supported by the mod? .. did I skip any steps? Should I use older mod?
I saw on the internet that these processors with some modification work and I thought they needed this modified bios. "I can't post the site where I saw them because I'm too new"
I hope you can help me with the problem and thank you in advance for any advice.

@Lost_N_BIOS @mitdal369 since we’ve had an influx of people with compatibility problems, perhaps it would be a good idea to edit the first couple of posts with links to the latest BIOS and a list of known working CPUs?

Did any of you guys get the BMC up and running?

I have the ASMB9-IKVM chip installed on the board and I can configure it in the BIOS but it is not getting an IP via DHCP. I have also set the IP address manually. But it is ignored and the OS gets a different IP via DHCP after booting the system.

hello please upload C621E SAGE 6201 mod BIOS to Gooledriver