After you run the following two commands.
FPTw.exe -me -f 7G7_0114.bin
FPTw.exe -greset
Nothing happened to you for illustration

I am very sorry I do not understand this talk
Sorry this is not my problem it's a personal problem
Please help with the simplest way
I am really sorry

The commands do not work
Please help

I changed the version of Windows from 32 bit to 64 bit
Yesterday it is possible to affect the operation of orders
After installing the definitions by the manufacturer of the device get errors in the device manager
This triangle is yellow
I hope the pictures help to clarify and solve the problem
Greetings to you

Plutomaniac thanks for your advice, I was not aware of #2 issues. And I have never seen anyone mention what you say at #1, I see FPT used with regions and full image all the time, even by you I thought, must be wrong
You should have warn me on this sooner , I've been having people fix things that way for long time and no one mentioned this before. However, thank you for the warning, I will have to retrain my brand and keep this in mind!
Also of note here, all this was fixed (except he needed to enable AMT via MEBx) until he removed the chip and put back on old BIOS without backing up the fixed BIOS!
Can you please tell me how to check if the ME below has programmed OEM data, so if he cannot boot DOS I can maybe have him flash this ME via FPT instead, if it's ready ME (It's not from SPI image, it's from MW FW Download on HP site)

@efraym - ME drivers need installed, and you need to follow the guides I linked you to in post #86 order to enable AMT at the BIOS level, it can only be done on your end via MEBx interface

Right now, I think BIOS and ME is fine, unless you are still, again, getting the 2233-HECI error at bootup?
If still 2233-HECI Error, please download the following ME and FW Update tool from the "DOS" Folder, then run this command from DOS Bootable USB or CD and then reboot
FWUpdLcl.exe 52501039.BIN

http://s000.tinyupload.com/index.php?fil...852817260455915

If you end up having to try from windows, use the following command instead
FWUpdLcl.exe 52501039.BIN -generic

I did see that, and wondered why! I didn't know FPT had/has issues like this with older versions, I've never seen such on newer FPT except by user error (ie trying to use .cap BIOS, but at least then you get yellow size warning)
Thanks for the heads up about this, I will now try to always send region files when having someone issue region based procedures! Bummer you are not thrilled by this, me either, and I hoped you'd jump in and solve this already
I thought I did have it all sorted, and then he erased our progress, but that was before I knew he had to enable stuff from the MEBx so we still wasn't sure at that time why things were not all working properly.
I suspect all will be fine again as it was, once he redoes the ME and gets rid of the HECI error. I'll have to get him into the MEBx quick once that happens, so he doesn't pull off the chip again yes, I know you are reading this @efraym - kidding around to give you a little laugh at our pain

Thank you for cooperating with
1. Error messages appear now
2233-HECI Error
2-I could not update ME drivers
Because of the error in the picture below

Sorry, I forgot FW Update tool will not work while ME is messed up.

Please flash this extracted ME using FPT from DOS, put FDO jumper in place first, then remove once done flashing
FPTw.exe -me -f Extracted_ME.bin

http://s000.tinyupload.com/index.php?fil...598223764608278

good morning
I do not know what to choose
1-fdo
2-PSWD

Put jumper on FDO, otherwise you cannot write to the ME region with FPT. Once done with above, remove jumper from FDO, paswd does not matter if jumper in place or not, it's only to clear password

Thank you very much for the clarification

After you run it
Pressing a character Y
What should I do

Please what I should do