Ok
I will try it

Bios backup done!
After that, first command gave error
"Error 114: image file 7g1_0127_fix_desc.bin" not found
I copied all files with flash tools in USB !!

All source files used in the commands I gave you are in post #6 of this thread, put those on USB. Copy your backup somewhere safe, where you wont loose or overwrite it.

here is the USB that i boot from with all content
can i rename the bin files to short name maybe

This is the log file after backup the bios and fails of the first command


02/12/19-11:31:38. ***********************************************************
02/12/19-11:31:38. Flash Programming Tool. Version 02/12/19-11:31:38. 5.1.0.1167
02/12/19-11:31:38. Copyright (c) Intel Corporation. 2007-2008
02/12/19-11:31:38. ***********************************************************
02/12/19-11:31:38. Number of ICH devices supported: 29
02/12/19-11:31:38. Southbridge: 3a14.
02/12/19-11:31:38. Base: 0x000000, Limit: 0x000FFF
02/12/19-11:31:38. Base: 0x260000, Limit: 0x3FFFFF
02/12/19-11:31:38. Base: 0x00B000, Limit: 0x25FFFF
02/12/19-11:31:38. Base: 0x001000, Limit: 0x002FFF
02/12/19-11:31:38. Base: 0x003000, Limit: 0x00AFFF
02/12/19-11:31:38. DumpFlashToFile(bios.bin, 0x0, 0xffffffff)...
02/12/19-11:31:48. FPT.exe exited with return code: 0
02/12/19-11:33:47. ***********************************************************
02/12/19-11:33:47. Flash Programming Tool. Version 02/12/19-11:33:47. 5.1.0.1167
02/12/19-11:33:47. Copyright (c) Intel Corporation. 2007-2008
02/12/19-11:33:47. ***********************************************************
02/12/19-11:33:47. Number of ICH devices supported: 29
02/12/19-11:33:47. Southbridge: 3a14.
02/12/19-11:33:47. Base: 0x000000, Limit: 0x000FFF
02/12/19-11:33:47. Base: 0x260000, Limit: 0x3FFFFF
02/12/19-11:33:47. Base: 0x00B000, Limit: 0x25FFFF
02/12/19-11:33:47. Base: 0x001000, Limit: 0x002FFF
02/12/19-11:33:47. Base: 0x003000, Limit: 0x00AFFF
02/12/19-11:33:47. Address = 0, Length = 1000
02/12/19-11:33:47. WriteFileToFlash(7G1_0127_fix_desc.bin, 0x0, 0x1000)...
02/12/19-11:33:47. FPT.exe exited with return code: 114
02/12/19-11:41:05. ***********************************************************
02/12/19-11:41:05. Flash Programming Tool. Version 02/12/19-11:41:05. 5.1.0.1167
02/12/19-11:41:05. Copyright (c) Intel Corporation. 2007-2008
02/12/19-11:41:05. ***********************************************************
02/12/19-11:41:05. Number of ICH devices supported: 29
02/12/19-11:41:05. Southbridge: 3a14.
02/12/19-11:41:06. Base: 0x000000, Limit: 0x000FFF
02/12/19-11:41:06. Base: 0x260000, Limit: 0x3FFFFF
02/12/19-11:41:06. Base: 0x00B000, Limit: 0x25FFFF
02/12/19-11:41:06. Base: 0x001000, Limit: 0x002FFF
02/12/19-11:41:06. Base: 0x003000, Limit: 0x00AFFF
02/12/19-11:41:06. Address = 0, Length = 1000
02/12/19-11:41:06. WriteFileToFlash(7g1_0127_fix_desc.bin, 0x0, 0x1000)...
02/12/19-11:41:06. FPT.exe exited with return code: 114

Can't see file extensions in your image, please enable file extension from explorer folder options. It says file not found, so obviously name or extension is wrong
You have jumper on correct?

jumper on FDO
File extensions I think it is correct
by the way I'm trying to use DOS FPT
is there any way to enable extensions on DOS
all i know it is always enabled in DOS

Can I run the command "fpt -me -f -generic 7G1_0127_fix_me.bin" from DOS, or it is Windows command only ?
Because including "-generic"

Everything looks correct? Yes, go ahead and try renaming the .bin files to short names with no underscores (Like FD.bin, ME.bin), maybe that is the problem. That's why I wanted to see extensions, to check maybe if something was named differently than the commands we're using, since it says file not found.
And yes, run all FPT operations from DOS only when possible, if you cannot get the above command ran in DOS remove generic and try again, if no luck go ahead and try in windows

OK
I will try now

finally done!
all commands goes correctly and asked me to reboot
after reboot got in bios load default setting and boot to windows
after that shutdown and remove jumper from FDO
back to run the pc and try to update the me with "FWUpdLcl.exe"
i tried both windows and dos versions and faild
error message: 8193 intel me interface : cannot locate ME device driver
how can i update it ?

What "commands went correctly" please tell me what all exact commands you ran that successfully completed

Run >> Meinfo -verbose
From DOS and take an image of the output (if error, remove -verbose). Copy MEinfo.exe from MEInfo\DOS folder of ME System tools package to USB, then run command

3 commands
I changed the first command bin file name to FD.bin, and the second command bin file name to ME.bin. Without generic
Flashed it from dos
It's flashed correctly with result 100%

fpt -desc -f FD.bin
fpt -me -f ME.bin
fpt -greset

Later I will put the image of meinfo ☺️

Great, that's good! Now you need to flash main BIOS and hopefully all will be fixed.
make sure you have 7G1_0127_fix_spi.bin on your USB, and leave jumper on, rename to spi.bin and use this command to flash >> FPT.exe -f spi.bin
Then once again run >> FPT.exe -greset

once done, after the greset reboot, remove jumper and test everything. If still not working, order CH341A and SOIC8 Test clip cable on ebay and wait 3-5 weeks for delivery (Or you can pay more $$ for faster shippers on ebay, or find in other amazon like shops etc)
CH341A Flash programmer - https://www.ebay.com/itm/142685058952 = $2.46
SOIC8 test clip cable - https://www.ebay.com/itm/382486015977 = $2.47