Maybe your shorts on CPU not correct?

i tested both of them already 2 pin 2 pin and 2 pin 12 pin

there picture attached from the 3007 AIO bios working with g4400 and getting post code 00 on 9600k
http://i65.tinypic.com/a1n4w7.jpg


https://dlcdnets.asus.com/pub/ASUS/mb/LG...R-ASUS-3007.zip

https://dlcdnets.asus.com/pub/ASUS/mb/LG...R-ASUS-3401.zip


Edit 1: I may have to AIO the 3401 and flash it to test with 11.7 ?

Yes, I would test your last thoughts, not sure why 3401 would be necessary, use the latest BIOS. Why are you using 3007 anyway?
Did you confirm your ME version in windows with other CPU, before trying 9600K?

ok i going try 3401 Make AIO push with Shell.efi and flash

there pic from actually non coffe working post code 00 bios

http://es.tinypic.com/m/kbsqol/4

Edit 1

flashed 3802 BIOS and ME still 11.6 9600k not tested now

see pic below

http://es.tinypic.com/m/kbsqq1/4

Edit 2

@Lost_N_BIOS

9600k testd still with 00 if i press cpu it still power on if i close the shoket post code get 00 and power off after 1 sec exactly same as 300x bios ME still 11.6

@Vaxter - try with ME 11.7 then, and make sure you are using latest version of AIO Tool (If you didn't download recently)

Have you also tested BIOS built with CoffeeTime?

i try to make coffetime bios 3802 now and flash, boot with g4400 and see if i get me 11.7xx also try the i5 9600k to allow flash bios i try to use again efi shell and flash it from windows using FTP as you said by now



Edit 1
@Lost_N_BIOS going to flash bios and i get this warning now using rencapsulated .cap file by coffe

http://prntscr.com/lwtf3k

@Vaxter - extract body from that capsule, you cannot use capsule BIOS with FPT
And, would be best to extract "BIOS Region" from the BIOS too using UEFITool and use that to flash with FPT, if only updating BIOS region via FPT (-bios)

@Lost_N_BIOS board bios is briked now it don´t recognize the g4400 and just gives me 00 no more fight 3 days with board for that

Edit 1
used flashback button with USB and default bios 3703 bios is ok now as default ME still 11.6 i can try extract bios region etc as you sayd and flash it

Edit 2

The USB board overcurrent protection or something is not properly working because all the usb ports except the port included on the usb-c side are gone not working it seems something related to overcurrent protection
when board boot bios usb´s are gone if i plug usb stick on those usb and try read usb with flashback it is working, if bios post all usb`´s are gone from this ports

Edit 3 Bios region extracted and flashed using fpt bios version now 3802 modded with coffe ME still 11.6 the i5 9600k still giving me 00 and g4400 its working

Edit 4 now i am going to get H310 mobo to ensure the i5 9600k it´s alive

Edit 5 @Lost_N_BIOS testing the i5 9600k on h310 motherboard and results are ok the cpu is perfcetly working ofc i clean pins al deleted pin mod to setup on h310 mobo and test it i have to found the way to get this cpu working on my asus M8R ;/

@Vaxter - sounds like there is an issue with the Asus BIOS probably, not fully programmed into the board. Did you reflash FD region too? I just learned this is required when you change ME SKU, see these posts #655 + 662-663 and 668
[GUIDE] Coffee Lake CPUs on Skylake and Kaby Lake motherboards (44)

So you will need to do pinmod or purchase a flash programmer and if BIOS is soldered to the board you also need to purchase SOIC8 Test Clip cable.

@Lost_N_BIOS Did you reflash FD region too?

A: ok for the last i going to try unlock FD region full and shoot efi trick then try to reflash FD region


@svarmod
@nch2312
Guys, you have a similar problems.
It's doesn't matter which ME version you using for now. 8700K and 9600K will work only if you will flash full mod bios image. All regions, include Descriptor.
ASUS and ASRock has blocked some regions at default. Thats why noone software tool won't flash it.

If you don't want to use SPI for some reason, there is only way exists - first unlock regions once with switching board to service mode. Then flash full image with FPT or AFU.
Don't forget power off and remove battery after flashing for correctly ME updating.
Info about service mode switching, focus on HDO_SDO method:

they say i can try it without SPI programmer right ?

Yes @Vaxter if you do pinmod then you can reflash fully unlocked FD using FPT, then you can reflash entire mod BIOS including FD (Make sure to unlock FD again in mod BIOS and any other in future, before you flash it, that way FD remains unlocked)

@Lost_N_BIOS i extracted te capsule supreme fx and i can see the audio chip ALC 1150 is very small more tath usual and pins are ver very small this is going to ve very hard to put fingers on it almost i can´t ui can uplad picture but my phone run out o battery

maybe my best choice is to hot swap bios chip on some mobo like asus p8z68 v pro and flash it ?

under supreme FX same chip as this picture below

http://prntscr.com/lxubft

pin 1 and 5 is correct for this chip but the chips is very small

Yes, @Vaxter, you may be able to force flash hotswap from DOS, but I'm not sure about that on a different model board. If you can find a software that will work from DOS on that board/BIOS, then you can maybe find an "Skip ID" check flag or "Force" flag etc
That's normal size Audio chip, yes pins are tiny (really not pins, connection is underneath the chip, only tiny bit on side). If you can touch the trace on the board it's same as touching the pins, maybe between side solder and trace pad you can get connection.
Make your wire with needles on the end, then it will be easy

@LittleHill Great!
I can't go over 103 Mhz. I tried several microcodes, MMTool, UBU, I tried ME 11.6 and 11.7, and Coffee Time 0.7.
Asrock fatal1ty z170 gaming k6 and i3-8100.
The motherboard has the Hyper BCLK Engine external clock generator but I haven't come up with a solution.
Maybe this motherboard can be solved?