Zitat

---

You will find the "best matching" Intel RAID ROM/EFI RaidDriver module version for the different Intel RST/RST(e) RAID drivers within the start post of this thread.

---

I know, but i have an Asus Z97m-plus, asus refuses to update the uefi modules... I'm running latest bios. Since the board doesn't support USB Flashback I don't feel safe modifying the bios.

Finally a WHQL set of the 14.x RST drivers.
Intel Rapid Storage Technology (RST) 14.0.0.1143 WHQL have now been released.
http://www.station-drivers.com/index.php....0.0.1143-WHQL/
I will be trying this WHQL RST set out with the latest Intel RST(e) RAID OROM 14.0.0.2234.

Hello my friend!

I just had to re-install Win7 (due to a failing HDD) and now, even though I'm following the steps I have before, I am unable to get the "IDE ATA/ATAPI Controllers" entries out of ATA CHANNEL. I tried using the Intel RSTe AHCI & RAID Drivers v13.1.0.1058 (64-bit) drivers, but it still says the IDE drivers are correct. I wish I could just add a pic here, instead of just a link (that would be a LOT easier). The system is an Asus Sabertooth Z77.

Thanks so much for any assistance!

LOL, yes, that's what I meant.

I get the following for the Hardware IDs
*Intel-1e02
*Internal_IDE_Channel

For the Intel(r) 7 Series/C216 Chipset Family SATA AHCI Controller - 1E02 I get the following:
-- All prefixed by PCI\VEN_8086&DEV_1E02&
*SUBSYS_84CA1043&REV04
*SUBSYS_84CA1043
*CC_010601
*CC_0106

Here is the DM screenshot - running Win7 SP1 with all current updates.

I've updated my Intel OP ROM to the latest: "Intel RST 14.0.0.2234 RAID Driver" and installed the "Intel RSTe Drivers & Software Set v14.0.0.1143 WHQL" Driver/Software set. After rebooting only the storage controller was updated to the latest driver under the "Storage Controllers" submenu in device manager. The default microsoft driver is still being used for the "Standard SATA AHCI controller" under the IDE ATA/ATAPI controllers submenu. Is this correct?

I'm running Windows 8.1 64-bit on ASUS P9X79-E WS with RAID-0 UEFI only, Intel mode set to RAID.

Ah that makes sense, after checking the vendor it belongs to the Marvell controller. The reason I'm using v14 is because earlier I tried to install "v3.8.1.1006 WHQL" but I kept receiving an error message saying this software is not compatible with my operating system so I ended up flashing the latest OPROM and just used v14 which installed without any issues. Only downside I can see so far is the Intel RST console reports two drives are failed I do have the option to mark them as OK but I figured it was a compatibility issue and haven't touched any of the settings within the console.

Zitat von Fernando im Beitrag #763

---

Zitat von Justin52 im Beitrag #762

---

The reason I'm using v14 is because earlier I tried to install "v3.8.1.1006 WHQL" but I kept receiving an error message saying this software is not compatible with my operating system

---

You probably got this message, because your Intel SATA RAID Controller has been set within the BIOS to "RST mode" (= DEV_2822) instead of the regular "RSTe mode" (DEV_2826).
According to my knowledge the Intel RST(e) Drivers & Software Set v12.9.4.1000 in combination with the Intel RAID ROM/EFI RaidDriver v12.9.0.2006 would have been the better choice.

---