Does the mod+signed variant Intel RST v17.9 driver offered is the 'Universal' driver dated on 02fev21 you have modded on 9may21 ?

@Fernando,
Yes, I have done Win-RAID CA import.
Hopefully I have done a "Restore Point" before the test .. because the system does not boot after modded v17.9 installed.
No abnomal message is reported during installation update v15 to v17. The usual reboot PC operation is requested at the driver update completion.
However, reboot does not work (circle logo infinite time).
Whatever the BIOS SATA Mode settings (AHCI or RAID), the boot process does not work !
The difference with your platform test is that your configuration has a standard SATA AHCI device, not a Array RAID0 SATA disks device.
Due to a Restore point I was able to re install the v15 situation.

Hi all.
I have Supermicro X11SPi-TF Mobo with Intel C622 chipset.
There are Sata and sSata Ahci/Raid.
I use Sata at Ahci mode with PCI\VEN_8086&DEV_A182&SUBSYS_094115D9&REV_09\3&11583659&0&B8
hardware ID.
I didn' t find the Dev ID at IDs list.
There is dev_a282 only.

Could you advise RSTe or at least RST drivers (supporting bothe Ahci/Raid modes) for the ID with RST UI for Windows 2016 ?

Intel Rapid Storage Technology (RST-VMD) Version 18.3.0.1003 WHQL

iaStorVD 18.1.6.1039 -> 18.3.0.1003

Hello @Fernando ! New to the site, think I'm on the right path but not quiet sure. Fernando, I have an Super Micro X10SRA Motherboard updated BIOS to Revision: 2.1a Running raid 10 , I have been unable to get windows to recognize my raid array, and after discovering your post and downloading the >Intel RSTe RAID Drivers & Software Set v7.5.0.1991 for Win8-10 x64< windows was able to load the driver in the iaStorB+iaStorE folder and finally pick up my raid array. After Installing Windows (Usb) it needs to reboot to finish installation and seems to lose the drives after reboot?

OS Windows 10 Pro ARCHT x64 DATE MOD. 4/9/2021, I upgraded Bios to 2.1a in hopes it would solve my issues, IRSTE sSATA Option ROM - 4.5.0.1012, 4x HDD's are all connected to the S-SATA0~3 , I-SATA0~5 ports are unused. Motherboard manual said All ports are used by the Intel C612 PCH chip, & Raid 0,1,5,10 is supported on all SATA ports. Trying to install windows off my Raid 10 array which is 4x WDC WD1003FBYX-0

Is seems he is right, from his manual:
"SATA Connections (I-SATA0~5, S-SATA0~3)Ten Serial ATA (SATA) 3.0 connectors (I-SATA0~5, S-SATA0~3) are sup-ported on the board. All SATA 3.0 ports are supported by the Intel C612 PCH chip. RAID 0,1,5,10 are supported on all SATA ports. These high speed ports support transfer rates of up to 6Gb/s. See the table on the right for pin definitions."

And the quick guide...

I thought by upgrading the Bios to 2.1a windows would finally be able to see my raid array with the new bios update, this was not the case as the issue still persisted. I have Sata and sSata tabs listed in the bios, I changed sSata from AHCI to RAID in the Bios and after reboot Ctrl+i now brings up the IRSTE Menu, this is where I am able to create my raid array. Motherboard manual said All ports are used by the Intel C612 PCH chip, & Raid 0,1,5,10 is supported on all SATA ports, I have all 4x HDDS on the S-SATA0~3 side, I-SATA0~5 ports are unused. I used Windows ISO tool to make a bootable USB, I am also trying to load the RAID driver off of a separate USB. Are you saying I download the wrong RAID driver?

Apologies I am confused, Should I "Upgrade the Intel RAID RSTe BIOS module(s) to the v5.5 platform and "downgrade" the in-use Intel RSTe RAID driver to the v5.5.4.1036." Or use "an Intel RST driver (instead of an RSTe one) for an Intel RAID array." Also if you could link files/attachment to use that would help a lot as I don't quiet understand all of the differences between RST vs RSTE and V5.5 vs V7.5