@EvieSigma - here, I found what I needed (Current microcode info - Rev 60B) from your screenshot images over at BIOS-Mods forum.
Here is mod BIOS with latest 2015 (Rev 612) microcode for 10676 instead of 2010 (Rev 60F) in the other mod BIOS you tried
http://s000.tinyupload.com/index.php?fil...181192220639971

After flash, clear CMOS and then load optimal defaults. Then set your SATA settings back to whatever you originally had set IDE, AHCI, RAID >> Very important if you are using RAID to set RAID again before booting to windows

I'd have loved to tell you it worked but it actually failed to flash and gave an error message! Apparently it failed consistency checks?

https://i.imgur.com/zeMB9iy.jpg

@EvieSigma - I thought that might happen. Can you flash from DOS, or from within the BIOS with a file, I can send you .rom or HDR instead of exe?
How did you flash DeathBringers exe, or did it pass those checks? This was first time I used this method on the exe, so I thought it could possibly not work, but it opened and error'd on my system same as the stock (after a few methods) so I thought I got it correct finally/
Editing the rom or hdr is much easier and done in a few seconds, but repacking the EXE is the issue, and I didn't think you could flash rom or HDR easily. There is ways, using Dell's tools, but I am unsure which are valid for your system

I flashed Deathbringer's mod from within Windows. I actually don't know how to flash a Dell BIOS from DOS, unless I could use a generic Phoenix flashing tool and a .rom file.

Most/many Dell I have used you can flash from within the BIOS somewhere, does your BIOS have this option anywhere, maybe on save/exit page or Info page, or a hotkey on bottom
If not, I am not sure if there is any generic tool that would let you flash from DOS, but there is specific Dell tools that you can use .rom and .hdr with, but I'm not sure which one works for this system (DCC - Dell Command and Configure or CCTK Dell client configuration toolkit )
But, you already have it updated to be compatible. If you need 2015 ucode as I tried to do for you I'm sure @DeathBringer will make a new mod for you if you ask him.

I should ask him how to fix the consistency check, I checked his mod exe and see he didn't change the header for size adjustment when he repacked the differently sized .qz/HDR file in there.
I assumed that would cause issue when I first did the change, so I corrected mine and it failed, so I put back to original and then it seemed OK when comparing to how the stock exe reacted when I ran it too.

Yeah, I looked up Dell Command and Configure and CCTK but neither one seems to support this system. I might try CCTK 2.2.1 anyway though.

@EvieSigma - Here is package I created with DDCU 3.1 using a modified HDR as source, leave the exe in folder when executing because during process it generates a bunch of files.
Close all open apps, stuff you need to save etc, then run the exe and wait 3-5 minutes as it updates system, then it will auto-restart once done flashing.
http://s000.tinyupload.com/index.php?fil...191881666293359

Then on reboot check current in-use microcode version using HWInf64 or AIDA64, if version 612 then success!

If fails, it may be due to I created the exe on my system, you may need to do it on your system instead. If you need to try that, and want the updated HDR let me know I will send to you with DDCU and you can create new exe on your end that way its made on your system.
I am unsure if it pulls info/settings etc form system to create the exe, that's why I said maybe it will fail due to being made on my system, I am unsure of what all it does during the exe creation process.

I think you should send those to me anyway, @Lost_N_BIOS, just in case, since it's going to take a little time to reinstall Windows 7 with the original CPU and then install your update.

EDIT: It turns out that it failed as it gave the update failed message once again and my microcode remains at 68 in HWinfo.

@EvieSigma - Sorry it did not work! I'm not sure how to do the exe properly like @DeathBringer did, wish he would reply here and drop me a hint If not, you could ask him at BIOS-mods forum to kindly make you another exe with 2015 version microcode.

Here is updated HDR and DDCU if you want to try and make an EXE on your end to see if that makes it work - http://s000.tinyupload.com/index.php?fil...958303488145238
To use DDCU, after install open the shortcut and it will open your browser, at the top section only, browse to HDR file, then still in top section on the far right there is a little blue text line to create the exe installer.

@Lost_N_BIOS well I'll be darned, it STILL failed, even when made on original hardware. I'll have to contract Deathbringer and see what he can do.

Yes @EvieSigma - I saw you mentioned that at BIOS-Mods, maybe that program isn't compatible with your system, I'm not sure.
Hopefully DeathBringer will give me some info over there, I hoped in right behind you to ask if he'd fill me in so I can do for others in the future too.

Hi,

i need to Update cpu10676_plat80_ver0000060C_2008-01-19_PRD_FBAC0EED but can´t find on Github the Microcode for this PlatformID.

Ideas ?

@Starfox

Maybe your platform was included in an other platform # since 2008 or someone forgot to add the newer code to the database. I suggest that you ask your question to Plutomaniac in this thread. It is the best place to get a precise answer to your question.

@Starfox - Because it was superseded by >> cpu10676_plat80_ver0000060F_2010-09-29_PRD_8FE1A1C7 and then platforms combined into 91 for your originally 80 (7) >> 91 now contains (0,4,7) >> cpu10676_plat91_ver00000612_2015-08-02_PRD_1750A2A6

So to update cpu10676_plat80_ver0000060C_2008-01-19_PRD_FBAC0EED to latest version you want >> cpu10676_plat91_ver00000612_2015-08-02_PRD_1750A2A6

Zitat

---

@Starfox - Because it was superseded by >> cpu10676_plat80_ver0000060F_2010-09-29_PRD_8FE1A1C7 and then platforms combined into 91 for your originally 80 (7) >> 91 now contains (0,4,7) >> cpu10676_plat91_ver00000612_2015-08-02_PRD_1750A2A6

So to update cpu10676_plat80_ver0000060C_2008-01-19_PRD_FBAC0EED to latest version you want >> cpu10676_plat91_ver00000612_2015-08-02_PRD_1750A2A6

---

Ok thanks