someone know what the "spread spectrum" is for ? and what is the good option : enable or disable ?
thanks

Press the "Alt" key with the item selected.. I added descriptions nad/or much better explanations for a lot of options.

ok. thanks :)

@ket well I am hoping you can help me if you have the time...I recently had to replace my C6H motherboard and I know...I made a mistake and got the gigabyte x470 aorus gaming 7 wifi...but no use crying over spilled milk. I have been working on the bios, with what little info is available. I am pretty satisfied with where I gotten the bios to, however I have few things that are just irking me with the bios that perhaps you might help me with.

1. Enabling the PBO options and scaler options I found that the F4e beta bios had these options exposed per a giga japan tweek back in may, however even using that does not show the options so I am not sure what gives.

2. EDC Relaxed Throttling option.

3. Exposing the memory fail_cnt as in the bios versus manually editing in the bios like I have.

Here is the latest modded version I am working with off the F4 official

https://drive.google.com/open?id=1UhexVM...hYn_pEQ2qVbbDyW

So I haven't found what causes/a way to reproduce the issue constantly, but it seems with a modified VCore the K7 tends to be a bit murderous by shoving ~1.52V into my 1700x.

Haven't tried the official F23 build either, so it could be an issue for all. Tried to go around with changing LLC and such, but it seems to be random on boot, and unrelated to that sort of thing. Haven't seen it happen yet by using voltage offset.

Just thought I'd make people aware of it, just in case, to check their readings, and I'll try to investigate further.

Hello, im new to the forum and i need some advice.

I have the 2600x along with the 370 k7. Q-flashed the modded f23 bios from ket. Have official f23 as backup too.
I've noticed in Ryzen Master that my cpu reaches the EDC limit almost too fast, and my all core boost is just 3975 while running Cinebench.
My temps are below 80c. I see no option under NBIO to change EDC limit. Only the temp and Wattage limit are there to change.
What can i do? Shall i flash the old f22 bios; Some1 here said it has all options enabled by mistake...

Thanks!

Zitat von mtrai im Beitrag #904

---

@ket well I am hoping you can help me if you have the time...I recently had to replace my C6H motherboard and I know...I made a mistake and got the gigabyte x470 aorus gaming 7 wifi...but no use crying over spilled milk. I have been working on the bios, with what little info is available. I am pretty satisfied with where I gotten the bios to, however I have few things that are just irking me with the bios that perhaps you might help me with.

1. Enabling the PBO options and scaler options I found that the F4e beta bios had these options exposed per a giga japan tweek back in may, however even using that does not show the options so I am not sure what gives.

2. EDC Relaxed Throttling option.

3. Exposing the memory fail_cnt as in the bios versus manually editing in the bios like I have.

Here is the latest modded version I am working with off the F4 official

https://drive.google.com/open?id=1UhexVM...hYn_pEQ2qVbbDyW

---

I'm taking notes to look at things in future guys but there is a board in much more dire need of my attention at this point in time so I'm preoccupied with that. I will look at the firmware for the gaming boards and see if there is anything worthwhile I can do in some updated releases. Oh, and B350 owners, you'll see some love too seems unfair to leave you out as F23 seems to be pretty decent. Took GB long enough though.

Updated modified X370 Gaming K3 firmware to F23M-D. Consider it a one-off.

@ket
Hello, awesome work! Would be possible a modded bios for the GA-AX370-Gaming-3 missing some voltage options and has a very limited offset voltage, It's a pain in the ass to have to start Ryzen Master to OC my cpu, didn't win the silicon lottery :(.

@0sk4r in theory you can extract the custom GB setup module and replace it with one from the Gaming 5 however there would likely be a lot of work to do to make it compatible. You could also try taking specific parts you want and modifying the existing custom setup module but that has problems of its own and likely won't work. I couldn't say more without looking at the setup module, either way you go though it is going to be difficult the best starting point would be to extract the custom setup module, convert it with IFR, and hope the options you want are just just being hidden with suppress constraints.

Zitat von IK4MS im Beitrag #905

---

So I haven't found what causes/a way to reproduce the issue constantly, but it seems with a modified VCore the K7 tends to be a bit murderous by shoving ~1.52V into my 1700x.

---

My apologies if this has already been answered but 61 pages is a lot to read and no search function available on mobile version.

Is there a mod or a way to unlock all rgb zones on the X370 Gaming 5 motherboard?

For some reason the color is stuck pulsing green and will not change in rgb fusion nor the bios. No recent bios changes have been made.

Thank you in advance.

Did you try clearing CMOS and re-flashing or loading optimized defaults again to see if that will help?

with my "X370 Gaming 5" (Ryzen 2600X + F4-3200C14D-16GVK) i get debug code "D5" before the next boot fails

so far only had happens when i shutdown - with better RAM resistance it works better