Specifically this one have:

hXXps://www.ebay.com/itm/SSU-SA3004-4-Po...rd/401741567473

What is the chipset of the card? I see nothing in its specifications.

From Product Description (almost at the bottom of page) on eBay:

*removed lines*
Product model: SATA3004
Number of interfaces: 4 port
Support mode: AHCI/IDE/Data disk
Maximum speed of single port in PCI-E2.0: 400MB
Applicable slot specifications: PCI-E (1X/4X/8X/16X)
*removed lines

HERE IT IS ----->Main control chip: ASM1061+1093
ASM1061 is an chipset, 1093 is (I think) port replicator. Natively ASM1061 have only 2 ports supported.

Hello, i purchased this card https://www.ebay.com/itm/Mini-PCI-E-PCI-...872.m2749.l2649. I saw in properties this PCI\VEN_1B21&DEV_0612&SUBSYS_10601B21&REV_01 so i downloaded a pack of drivers for ASMedia 106x from here Recommended AHCI/RAID and NVMe Drivers. My windows 7 does not recognise the drives connected on this card and when i install the drivers my system cannot boot again. Any idea?

Is anyone using the Delock 89359?

https://www.delock.com/produkte/G_89359/merkmale.html

I would like to know if the SATA ports on this card are bootable or not.

Just registered to share some information.

There 2 versions of ASM106X ROMs. One for motherboards is that around 32KB, and one for add-on cards that is around 128KB.

The latest version for the add-on is 1.90 and is available here: http://ableconn.com/upload/ASM1062%20FW_...-RE1062.A19.zip

@DavidSar

Is this version intended for any ASM106X card or only for ASM1062? Did you try flashing it yourself?

Don't know about 1061, but worked fine for me on SilverStone ECS03 PCIe card, and some other generic card with ASM1062.

I have ASUS Z370 Hero X WiFi AC motherboard with the latest BIOS 2301 and Windows 10 x64 LTSC. How can I find out:
1. Which ASMedia SATA Controller my motherboard has?
2. What are the latest drivers for my motherboard's ASMedia SATA Controller? Where can I download them?
3. What is the latest firmware for my motherboard's ASMedia SATA Controller? Where can I download it?
4. How can I flash my motherboard's ASMedia SATA Controller to the latest firmware version?

Zitat von gitsov im Beitrag #192

---

So now my question:
I have (sh!tty) AssRock J4105-ITX mainboard, which I am using as NAS. Board have soldered Quad Core Celeron processor and have no CSM in BIOS (AssRocks!) so it's UEFI only.
There is an 2-port Intel SATA3 controller and Asmedia 2-port 1062 (according to lspci from Linux) controllers onboard. I can boot from drives attached to both of controllers and they are shown in BIOS.
I've bought SSU-SA3004 v2 PCI-E x1 board (that green one with switch and 4 ports), but even after update to 4.27 AHCI ROM is not listed as possible bootable device in my secondary PC's Mainboard set at CSM/UEFI or No CSM Boot settings (Board is AsRock H81-DG4). It is listed only in Legacy mode as boot device. My goal is to expand NAS with that 4 ports and if possible to make that card bootable (and future proof), but in BIOS MMTOOL shows only ASM1061SataDriver and OpROM. Extraction of that driver generates 9KB uncompressed file and comparison with Hex editor shows that OpROM (32KB) does not contain driver . My question is:

Is there a way to combine both UEFI driver and OpROM on card's flash chip?

I know that, probably card will probably work with disabled boot support via switch as boot device, as it will "share" driver from onboard controller (maybe I shoud disable onboard controller too), but I am looking for variant when I replace board with another one which does not have this controller soldered to use it.

BTW card have two flash chips ([s]Puya PH25Q40B[/s], recognized as EON EN25F40 by Asmedia updater, see attached picture) and I am assuming that switch on top enables 1 with AHCI ROM (left position), second with IDE (right position) and in the middle position (NoBoot), it just disables both SPI chips.
*chips aren't Puya - got fooled as on my other 88SE9215 is with that chip, but markings looks similar.
*This controlles does not get listed as boot device both on AsRock H81-DG4 and J4105-ITX. Tried with AHCI/IDE/NoBoot positions on switch.

---

Hello Guys! I currently have an X79 ASRock Xtr4, with an onboard ASM1061 sata controller that isnt working at all. i bought the mobo used and since day 1 it wasnt working. Anyone can help me to update the OROM of my motherboard bios? Is flashed to 3.40 latest beta bios. I really need this SATA3 port since my motherboard has only 2 sata3 and 4 sata 2.

Asmedia ASM-106x/R Sata 6G Controller Firmware v190920
Asmedia ASM-106x/R Sata 6G Controller Firmware v190920 (Raid)
Asmedia ASM-1x6x Sata 6G controller Drivers Version 3.3.5.0 (win 8 and up)
Asmedia RAID Manager Tool (ASM-1062) v3.130 or Recommended AHCI/RAID and NVMe Drivers

Please back up first,test it,then share the result with device info (id) so others can benefit

Is anyone using a SD-PEX50055?

https://www.sybausa.com/index.php?route=...&product_id=177

Is this card bootable?

can't say for sure,depends on the motherboard.there is a possiblity that some old boards may not see it as bootable and since SATA interface shows empty you may not be able to use it
things you may need are CSM,Launch Storage OpROM Policy,UEFI mode

Zitat von onuracengiz im Beitrag #209

---

things you may need are CSM,Launch Storage OpROM Policy,UEFI mode

---