I just install XP SP3 with your Sata driver with DEV_A282 for brandnew Asus Apex ROG Maximus X,
chipset 1151 with Z370,
this I have not seen before on an Intel i-8700 and was 4 days hard work for me:)),
have a nice day
Dietmar

Hi Fernando,
first I make a try with nlite to integrate the Sata driver for DEV_A282 (Asus Apex ROG Maximus i-8700k), this fails.
Then I use Winbuilder. This is a very good program and works here also.
The floppy F6 methode does not work for me.
With USB floppy and F6 I can formate the harddisk, but then crashes after 50 % install
with error and blue screen page_fault_in_nonpaged_area stop: 0x00000050 setupdd.sys
The same error is reproducible. You need to hit also F7 during install (for no ACPI Bios).
So I came to the idea to install from USB.
The program WinSetupFromUSB starts, but than comes blue screen with 0x07b, driver is gone.
Then I google a lot and find the thread
"How to install Windows XP on a 2016 Skylake Asus Z170-A motherboard"
This also gives a message firadisk.sys not found. But I have the CD install disk made with Winbuilder
and I can continue with install from D:\ from this CD.
Now I install a gfx 980 with inf modification for XP, a Asus PCIE soundcard for XP and a networkcard for PCIE from TP link for XP also. I will tell about results to have XP, Win 7 and Win 10 on a brandnew Compi from November 2017:)),
have a nice day
Dietmar

Hi Fernando,
driver is from Universal 32bit Intel RST AHCI+RAID driver v11.2.0.1006 mod+signed by Fernando

iaAHCI_200 = "Intel(R) SATA AHCI Controller DEV_A282 added by Fernando"

This DEV_A282 I found in my Win 7 installation. Very strange is that I note,
that this number changed in Win 8???
The problem with blue screen 0x050 setupdd.sys direct before reboot after XP installation I have also
on my iaAHCI_ICH10R = "Intel(R) SATA AHCI Controller DEV_3A22"
compi. May be this error depends on the whole size of the Harddisk, I have 2 TB,
have a nice day
Dietmar

PS: I modded AHCI driver also by myself. Always with the 2 TB harddisk I get blue screen 0x050 setupdd.sys on 2 different computers.

Hi all,
I got in qemu the same error page_fault_in_nonpaged_area stop: 0x00000050 setupdd.sys.
The AHCI driver is not correct installed. This belongs not only to the Apex motherboard.
I also cant install AHCI driver with this method on my old compi with ICH10-R Sata.
So I think, integrating sata drivers went wrong via Winbuilder. nlite also does not work for me.
I look at the harddisk what happens during install.
The drivers are on the harddisk, but in the folder "driver", the txtsetup.oem is empty.
On the Winbuilder CD with the integrated Sata drivers is the same folder named $OEM$ and in its subsub folder is a new folder kdrv0, which contains the Sata driver with *.sys and *.inf and also filled txtsetup.oem.
Now I make a try with qemu, to install the sata driver,
have a nice day
Dietmar

I made one before using the drivers from driverPacks [http://driverpacks.net/downloads], but they only have company drivers upto september 2012

PCI\VEN_8086&DEV_8C01&SUBSYS_05BE1028&REV_04\3&11583659&0&FA

made several attempts, the result was blue screen every time

I made 5 .isos and 5 cds, everyone had your iaStor in it, everyone stopped at blue screen