Zitat von Fernando im Beitrag #599

---

Ok, attached are the mod+signed 32bit and 64bit NVIDIA nForce SATARAID drivers v11.1.0.43, where the included INF files have just been modified by me according to your proposal.

Any feedback is much appreciated!

---

I am having the same problem. Tried a BIOS update, checked the boot config, nothing seems to work. Might be time for a new motherboard, but I did read something about PUIS (power up in standby mode) which may or may not be the problem. Definitely a combination of Nvidia nForce drivers and Windows 10. I am also considering a PCIe RAID controller instead of swapping out the board. I think the bigger problem will be that the RAID will probably need to be rebuilt if I go that route.

I am going to roll back the update until I hear if there is a solution that doesn't involve hardware upgrades!

Hi @Fernando,

My original plan was to post on this thread (but I wasn't sure which post to reply to)
NVIDIA: Optimized nForce Driverpacks for Vista/Win7-10
However, I think my question does apply to your recent edit of your own post.

Thank you very much for maintaining this forum. I have now read much of the information you have provided over several years, as well as your updates, in the last week or so. These are excellent and do not exist in any useful form elsewhere.

I am just trying to decide my next steps with my machine, and perhaps to add some info for other users. I have put quite a lot
of details here for clarity. You are very welcome to edit/shorten this post as you feel is suitable.

I'm having problems with my machine (details in my signature) that had successfully upgraded from Win 8 to Win 10 32-bit (on 26 July 2016). I have a single disk (raid 0 disk array), which both contains the OS and is used to boot the machine.

On Friday 12 Aug, the machine would not boot. In my efforts to resolve this I have returned to Win 8 (via the return to a previous build option). Win 8 runs without problems. However, repeated attempts to upgrade to Win 10, from 12 Aug to 14 Aug, failed with the
0xC190010 - 0x20017 error. Mostly from this site, I understand this is related to nvidia raid drivers. The event log contains several nvraid error 11 messages.

By the way, I did not choose to install the anniversary update, and am not aware of any system message about it.

I was going to ask about creating a custom Windows 10 image, with NTLite and following your guide:
[Guide] Integration of drivers into a Win7/8/10 image
The steps in your post suggest this is not necessary. Am I correct? In step 1, you refer to a "previously running system". Does this refer to both Win 8 and Win 10? My machine (I am guessing) had no previous Win 10 build to return to.

If I get back to Win 10, do I need to stop the drivers being overwritten by Windows 10 (whether due to updates or other methods)? If so, is there a post on this site that gives clear advice? I have a concern that if I do get the machine back to Win 10 and do nothing, I may end up with the same problems I have now. Or is it the case that the modified certificate prevents Win 10 from unhelpful driver updates?

As I have a working Win 8 system, there is no immediate need for me to resolve this problem, but I would prefer to return to Win 10 (in part so I can upgrade to 64-bit).

Any advice is appreciated.

Many thanks, Jon

Hello Fernando,

I used your guide to get access to my nvraid.
The current situation is that I have V11.1.0.43 drivers in place for Sataraid and Nvidia_Sataide controllers.
In the details I saw the connected ssd for each controller, but I was not able to get the generic_disk_array devices updated with the right driver.

Your help is appreciated.

I have currently no idea where I make the mistake ?

Thanks in advance.

Ulrich

Hi,

did you use the driver from Post #119?
can you share the Device IDs of your Generic SCSI Array Devices?

Embarassing: I definitely have the issue (and cured it with Fernando's driver), but checking winver I am still on 1511. Therefore the Problem seems to be with the Aug 9 Update ( https://support.microsoft.com/en-us/kb/3176492 ) and not 1607.
I suspect the kernel mode driver update to be the bad guy that breaks device enumeration: https://support.microsoft.com/en-us/kb/3177725

EDIT by Fernando: Post number corrected (caused by its movement to this new thread)

I just tried installing the driver pack included in post #119. I was able to install the driver for "NVIDIA nForce Serial ATA Controller" and "NVIDIA nForce RAID Controller"
But when I try to install the driver for "NVIDIA nForce RAID Device" I get an error that it can't find a suitable driver for my device.
I think you've removed too many lines as I can't see any that match my Hardware ID's in the version in post 119.

The moded 10.6 driver worked ok.
Here is the Device ID from my system:


EDIT by Fernando: Post number corrected (caused by its movement into this new thread)

Zitat von tandeejay im Beitrag #127

---

I think you've removed too many lines as I can't see any that match my Hardware ID's in the version in post 119.

---

Hi,

yes I used the driver from #119. will check later this evening the *.inf file I used.
Maybe there is the problem.

I try to use have disk but always get the error no suitable driver found.
It was late yesterday evening :-)

Thanks and regards,
Ulrich

EDIT by Fernando: The above mentioned post number has been corrected by me to avoid any misunderstanding by the visitors of this new thread. Due to the extraction of this discussion from the former thread all post numbers have been changed.

Hello all,

the latest drivers from post #119 are working fine for me. I used not the latest rar-file yesterday evening.

Thanks for your effort and help.

Regards,
Ulrich

EDIT by Fernando: Post number has been corrected by me. This is a new thread with new post numbers.

Zitat von opel07 im Beitrag #128

---

Zitat von tandeejay im Beitrag #127

---

I think you've removed too many lines as I can't see any that match my Hardware ID's in the version in post 119.

---

well, this line should work for you as it did for me:
%NVRAID_DESC%=nvraid,SCSI\__NVIDIA_______Raid_Disk_
-> did you install with "Have Disk" and provide the correct folder?

---

It looks to me like the following line should be added as it might be common amongst more systems.
%NVRAID_DESC%=nvraid,SCSI\Array__NVIDIA
This is the only line from the 10.6 version that matches any Hardware ID's in my system.