Last EVGA Micro2 Bios 2.01 information:

Intel(R) MEInfo Version: 9.1.20.1020
Copyright(C) 2005 - 2014, Intel Corporation. All rights reserved.

Intel(R) ME code versions:

BIOS Version: 2.01
MEBx Version: 0.0.0.0000
Gbe Version: 0.1
VendorID: 8086
PCH Version: 5
FW Version: 9.1.35.1006 H
LMS Version: Not Available
MEI Driver Version: 11.0.5.1189
Wireless Hardware Version: Not Available
Wireless Driver Version: Not Available

FW Capabilities: 0x00100940

Intel(R) Capability Licensing Service - PRESENT/ENABLED
Intel(R) Dynamic Application Loader - PRESENT/ENABLED

TLS: Disabled
Last ME reset reason: Power up
Local FWUpdate: Enabled
BIOS Config Lock: Disabled
GbE Config Lock: Disabled
Host Read Access to ME: Enabled
Host Write Access to ME: Enabled
SPI Flash ID #1: C22018
SPI Flash ID VSCC #1: 0
SPI Flash BIOS VSCC: 20052005
BIOS boot State: Pre Boot
OEM Id: 00000000-0000-0000-0000-000000000000
Capability Licensing Service: Enabled
OEM Tag: 0x00000000
Localized Language: Unknown
Independent Firmware Recovery: Enabled

MEManuf Information:

Intel(R) MEManuf Version: 9.1.10.1000
Copyright(C) 2005 - 2014, Intel Corporation. All rights reserved.


Error 9271: Flash ID 0xC22018 Intel(R) ME VSCC value mismatch
Programmed value of 0x0 doesn't match the recommended value of 0x2045
See PCH SPI programming Guide for more details

Error 9271: Flash ID 0xC22018 Intel(R) BIOS VSCC value mismatch
Programmed value of 0x20052005 doesn't match the recommended value of 0x2045
See PCH SPI programming Guide for more details

Error 9296: MEManuf Test Failed

I am using Intel ME System Tools v9.1 r7 tools, I always check before do a firmware update from Original BIOS manufacturer the MEInfo and MEManuf result but this is the first time I got MEManuf test failed with the original manufacturer BIOS

I am trying to do a ME firmware update to Intel ME Firmware v9.1.37.1002 (1.5MB) but first I want to clear up why the MEManuf test is failing with the original BIOS firmware manufacturer

Thanks

Mauricio Ramirez

Any comments?

Thanks plutomaniac

I did not changed the SPI chip at all, it is a new board that I just bought. I was plannning to do ME firmware update but before I do anything I always run MEinfo and MEManuf first to check that everything is fine. Thats when I got the error. There is anyway to fix it? Why a new board can give that error?

Thanks

Mauricio Ramirez

thanks here it is the result of fptw -d of the bios file (.bin)

C:\ME\ME\Flash Programming Tool\WINDOWS64>fptw64 -d 1E095201.bin

Intel (R) Flash Programming Tool. Version: 9.1.10.1000
Copyright (c) 2007 - 2014, Intel Corporation. All rights reserved.

Platform: Intel(R) C610 Series Chipset
Reading HSFSTS register... Flash Descriptor: Valid

--- Flash Devices Found ---
MX25L12805D ID:0xC22018 Size: 16384KB (131072Kb)

[1E095201.bin] file already exists
Do you want to overwrite file? Y/<N> or q to quit : y


- Reading Flash [0x1000000] 16384KB of 16384KB - 100% complete.
Writing flash contents to file "1E095201.bin"...

Memory Dump Complete
FPT Operation Passed

and here it is the result of MEManuf -EOL as well:

C:\ME\ME\MEManuf\Windows64>MEManufWin64 -EOL

Intel(R) MEManuf Version: 9.1.10.1000
Copyright(C) 2005 - 2014, Intel Corporation. All rights reserved.

Error 9311: CF9GR is not locked
Error 9283: Region access permissions don't match Intel recommended values
Error 9310: Intel(R) ME is still in Manufacturing Mode
Error 9271: Flash Id 0xC22018 Intel(R) BIOS VSCC value mismatch
Programmed value of 0x20052005 doesn't match the recommended value of 0x2045
See PCH SPI programming Guide for more details

Error 9271: Flash Id 0xC22018 Intel(R) ME VSCC value mismatch
Programmed value of 0x0 doesn't match the recommended value of 0x2045
See PCH SPI programming Guide for more details


Error 9322: MEManuf End-Of-Line Test Failed