Hello Fernando
Thanks for the hard work that you are doing to us.

I have a problem that i can't change or replace the orom irst raid for sata -13.1.0.2126 with orom irst raid for sata -14.8.0.2377 and
efi irst raid for sata -14.8.0.2377 i want them to v11.2.0.1527 trim with the update intel cpu microcode to the latest.
I can't upload the bios file because the capacity it's RAMPAGE-V-EXTREME-ASUS-3501.CAP i upload the images.
Can you help me do the rom for me or anyone else? it will be much appreciated.

@Fernando
Thanks

Zitat

---

Question: Why do you want to replace the original Intel RST RAID ROM modules at all? These modules will not be used, if you are running or install the OS in UEFI mode (which is absolutely recommended for your modern system).

---

I don't have good knowledge i thought if i do this will speed things up.
Can you please do me the efi irst raid for sata -14.8.0.2377 to v11.2.0.1527 only with Intel CPU microcode to the latest or if you can do something good for this rom RAMPAGE-V-EXTREME-ASUS-3501.CAP i mean i want it to be best for performance modified by you and upload it to me?



Best Regards
rom

I've several sata usb 3.0 pcie cards provided by vl805 or marvel chipset which hangs system if plugged into 4coredual-sata2 So what to do to implement thir bios into the bios of the mainboard and where to get those firmwares? PAY ATTENTION: the login into this site is claimed NOT SECURE BY CHROME (so if it is not secure toi enter this site try to make it secure! thanks)

Hey Fernando,

First off, I appreciate your taking the time to work on this for us.

My System:
i7-3930k
BioStar T-Power x79
Intel SSD6 M.2 256Gb
XINY M.2 NGFF PCIe x4 SSD to PCI-E x4 adapter card - It is NVME - link here:
https://www.amazon.com/gp/product/B01N4L...2?ie=UTF8&psc=1

Win10 Pro64 Bit

Here is what I have done:

Flashed my BIOS to most recent.
Disconnected my SATA Boot Drive (left 3 slave drives connected - no OS on any of them)
Booted from USB, the M.2 Adapter showed up as an option to install Win10 on, so I installed Win10 on the Adapter/M.2
Rebooted, and in BIOS, Windows Boot Manager DID show up as an option.
At this point, I was cheering!
However, it will NOT boot from it. Insert proper boot device error.

What I DIDN'T do:
I Modified the most current BIOS and inserted the NvmExpressDxE_2. It inserted successfully, no problems or errors, just didn't flash the BIOS with the Modded File - scared to brick it.

What I tried:
UEFI enabled and Disabled - same Insert Proper Boot Device message.

Any advice would be much appreciated.

Thanks a ton!

-Gonz

Zitat von Fernando im Beitrag #157

---

If you want to get the NVMe SSD bootable, you have to flash the modded BIOS into the BIOS chip of your mainboard.
The related guide is within the start post of >this< thread.

---

Hi,

I finished my firs BIOS modding. I want to ask is it ok and can i safely flash my bios.
Here is the original Bios:
https://1drv.ms/u/s!AkAjWEhvld_j_XUzZ26cdEbAmwgn

Here is the modded Bios:
https://1drv.ms/u/s!AkAjWEhvld_j_XZUsGJwkOybTcwP

I have a problem with windows 7, 8.1, 10 bootable usb. It shows me worker thread has returned at bad irql. I can successfully boot from FreeDos and linux usb. Does flashing my bios will solve this issue. Can i insert other firmware in this file like firmware for hd audio controller, usb 3.1 controller, WD10EZEX-08WN4A0 firmware. I suspect for firmware corruption. And when i update the LAN firmware it creates a file _BootAgentCL_15B8.lom https://1drv.ms/u/s!AkAjWEhvld_j_XgNpwjNi4RoK0mT . For what purpose is that file.

Best Regards

I forgot to tell you about my system:

ASUS Maximus VIII Ranger
i7 6700K
32gb kingston hyperx fury 2400
cooler master V650

Best Regards

Another think. If i flash the bios with the modded one can revert changes with asus bios flashback.

Best Regards

that will revert CPU microcode update wright.