everybody
Hello, I will not English, so I use the translation software will be my problem to you, if there is a wrong place, please forgive me, thank you
I have a dx79to Intel motherboard, I encountered two problems:

1, Intel motherboard BIOS is *. Bio, can not use the bio2ami software to get useful BIOS, then a long time can not be used to update the Intel RST ubu ROM. What should I do to solve this problem

2, I want to enable the x79 raid functionality, I in the BIOS open raid computer installed only a hard drive, through the CD-ROM installed win7 pro, to the installation interface, I by 3.6 rste F6 loading driven, I can see the hard disk, but setup told me "Windows cannot be installed to the disk, the computer hardware may not support booting to this disk. Make sure the disk controller is enabled on the BIOS menu of the computer.

I want the result is that X79 enabled raid, in the RAID 0 can be used under the trim

I did a search through Google, but did not find a suitable solution, Can I get help here? thank you

This is a very good forum, we look at foreign forum is very slow, in this forum I learned a lot of useful things, still thanks to reply, but second questions, do you know what is going on? I read your post, select the driver 13.1.0.1058 rst, but in the installation of this F6 can not load the driver, but in the AHCI mode to use the drive, which is how it happened?

SATA Mode ：AHCI
SATA Controller：Intel C600 series chipset SATA AHCI Controller（only 1 Controller）
HardwareIDs：
PCI\VEN_8086&DEV_1D02&SUBSYS_49538086&REV_05
PCI\VEN_8086&DEV_1D02&SUBSYS_49538086
PCI\VEN_8086&DEV_1D02&CC_010601
PCI\VEN_8086&DEV_1D02&CC_0106

Unable to install the system with raid, so I do not know the relevant information under the raid mode

SATA Option ROM - 3.5.0.1005

I understand these operations, but also the operation

I sort out the problems I have encountered：

1, Intel DX79TO this motherboard may not have ROM RST, it is only RSTe ROM (in the BIOS settings, there is no RAID mode choice option, only RAID this option, so it is RSTe mode 。

2, the question now is, I entered the win7 installer, F6 loading the Intel RSTe driver v3.x.x.xxxx or v4.x.x.xxxx,I can see the hard drive. but cannot be installed, windows prompt "Windows cannot be installed to the disk, the computer hardware may not support booting to this disk. Make sure the disk controller is enabled on the BIOS menu of the computer

Which partition of which Disk drive did you select, when you were asked where to install the OS?
Only a hard disk is connected with the computer, so I choose Win 7 installed on the hard disk

Which partition table did you choose (MBR or GPT)?
F6 after installing the driver, through the Diskpart, the hard disk is MBR, but whether I choose MBR or GPT, will appear unable to install tips

Why do you want to run the Intel SATA Controller in "RAID" mode at all?
Why choose RAID, because I want to be in the second 、 third hard disk using RAID 0

I watched you give this connection, the reason is because the connection in the third party SATA controller, but my motherboard no third party is directly connected to the X79 Sata controller chip.
Seems to be very difficult to find what causes this problem, 3.8 in the evening, I in an accidental situation can be installed, but I don't know what is the reason, also does not allow it to reproduce.

Zitat von linkpark007 im Beitrag #1

---

[...]I have a dx79to Intel motherboard [...]
1, [...] a long time can not be used to update the Intel RST ubu ROM. What should I do to solve this problem
2, I want to enable the x79 raid functionality, I in the BIOS open raid computer installed only a hard drive, through the CD-ROM installed win7 pro, to the installation interface, I by 3.6 rste F6 loading driven, I can see the hard disk, but setup told me "Windows cannot be installed to the disk, the computer hardware may not support booting to this disk. Make sure the disk controller is enabled on the BIOS menu of the computer.
I want the result is that X79 enabled raid, in the RAID 0 can be used under the trim
I did a search through Google, but did not find a suitable solution, Can I get help here? thank you

---

fsutil behavior query DisableDeleteNotify
 

If you get "0" as answer = TRIM OK
If you get "1" as answer = TRIM not working!

Regards
iddqd

P.S.: I only check here few times a month. Please excuse me if I do not answer for a long time.

Zitat von Fernando im Beitrag #11

---

[...] If the user wants to know, whether TRIM is active within the target SSD (inside or outside a RAID array), he has to do an appropriate TRIM check (look >here<).

---