@RN53:
Welcome to the Win-RAID Forum!

The thread, which matches the best your request is >this< one and you will find the related guide within the start post of it.
The only usable Intel AHCI driver is the modded Intel RST driver v11.2.0.1006. Don't forget to check the DeviceID of your on-board Intel SATA AHCI Controller, before you start with the integration of the Intel AHCI driver.

Zitat von RN53 im Beitrag #946

---

I have the iso burned to a usb and it is recognized and goes through loading steps, but then gives blue screen error of ACPI compliance issue. I was told your AHCI drivers would work here.

---

@aaa839:
Each user has to find out him/herself, which is the best AHCI/RAID driver for his/her specific system.
If you want to know, which Intel AHCI/RAID driver I recommend to use for the different Intel Chipset systems, you should look into the start post of >this< thread.

@Rio:
Welcome to the Win-RAID Forum!
Without any information about
a) your system (Chipset, OS etc.),
b) the SATA mode (AHCI/RAID) of the Intel SATA Controller,
c) the reason for the installation of a modded driver,
d) which specific driver you have tried to install and
e) how you tried to manage the installation,
I cannot help you.

Regards
Dieter (alias Fernando)

@Rio:
Thanks for the details, but you didn't answer the most important questions:
1. Which is Intel Chipset has your Mini PC?
2. Which OS are you running?
3. Which is the SATA mode of your on-board Intel SATA Controller?
4. Which SSD model did you buy, where did you connect it and which protocol (AHCI/RAID/NVMe) does it use?
5. Which is the name of the mod+signed driver you tried to install?
6. How did you install the driver? The driver of which device did you update?

Update of the Start Post:
Changelog:

• new:
  • mod+signed 32/64bit Intel RST AHCI+RAID drivers v16.3.0.1007 dated 01/18/2018, modified and digitally signed by me at 05/03/2018
  • Universal 32/64bit Intel RST Software v16.3.0.1007 dated 01/30/2018

1. These drivers are only usable with Win8, Win8.1 and Win10.
2. Intel RST(e) drivers of the v15 and v16 platform have been designed and optimized by Intel just for the newest Intel Chipsets from 100-Series up.
   Due to the modification of the related INF files the above listed Intel RST drivers will be installable onto older Intel Chipset AHCI/RAID systems, but may not properly work. Users with an older Intel Chipset system should better take a driver, which belongs to the v12, v13 or v14 platform. I am not responsable for potential problems they may get after the installation of these newest mod+signed drivers. It is strongly recommended to set a "Restore Point" before starting with the driver installation!
3. If not already previously done, don't forget to import the Win-RAID CA Certificate, before you try to get any of my mod+signed drivers installed. The Certificate itself and the related CMD file are attached to all my mod+signed driverpacks.
4. Due to new security features of Win10 you may have to execute the CMD file from within the Command Prompt or Windows PowerShell (both options have to be run as Admin).
5. >Here< you can get additional informations about "modded" drivers and >here< about how to get them properly installed.

@Rio:
Thanks for your reply.
I suspect, that your system drive is running in AHCI mode and that your on-board Intel SATA AHCI Controller has the DeviceID DEV_5AE3.
If I should be right, only the generic Win10 in-box MS AHCI driver (and no original Intel AHCI driver) natively supports your on-board Intel SATA AHCI Controller.
Some of my mod+signed Intel AHCI drivers are usable as well with your system, but these are the pre-conditions:
1. Before you start with the installation, you have to import the Win-RAID CA Certificate.
2. Make sure, that the prefered mod+signed Intel AHCI driver version definitively supports the DeviceID of your on-board Intel SATA AHCI Controller (it is probably DEV_5AE3).
3. You have to manually update the driver of the Intel SATA AHCI Controller. Maybe the installation has to be forced by choosing the "Have Disk" option.
4. When you are asked, which specific Intel SATA Controller shall be supported, you have to choose the one with the DeviceID of your on-board Intel SATA AHCI Controller.

@Rio:
After having done a look into your attached screenshots I cannot identify the Intel driver version you have tried to install.
Why did you install the related driver at all?
Regarding the solution of your current boot problem I recommend to boot off an USB Flash Drive containing the original Win10 Image and to choose the "Repair" option.
You should be able to restore your previously working system by choosing a certain previously set "Restore Point".