thetruthisalie

Zitat

---

I was rock stable on 13.1.x orom

---

Same here, but on Win8.1 [x64]

Zitat

---

I updated to 13.2.x and started noticing extreme slow down as well. I reverted to 13.1.x and all is great.

---

Very useful notice! Thank you!

Zitat

---

Perhaps issue with 13.2 or maybe 13.2 better off with higher version driver.

---

That's a big question. I would like to know for sure, which one version of OROM/EFI suites better for Z77.

----------------
Ideally, we need new OROM/EFI modules for old systems from Intel, more compatible with vulnerability fixes and v16-series of the drivers.

After some tests (Win8.1 / Win10), 1 SATA SSD + 2 SATA HDD, I can say:

With fully activated Meltdown/Spectre FIX, the absolute winner Drivers is v16 (the last).

I case I'm on AHCI-mode and don't have RAID, then SATA IRST OROM/EFI does no influence on my tests.
In-RAID mode feedback about drivers have to be collected also.

--------------------------------------

@ Fernando

Your Drivers/Software v16 modded archive names at MEGA have the version numbers 1068. Should be 1086 ?

@Fernando
Thanks for the update.
I suggest you replace also modded v14.8.17.1065 with a modded v14.8.18.1066.

There are official ESD files of the upcoming Windows 10 Update (Redstone 4, ver 1803) and you have to be careful if you are using the modded Intel drivers because after the first reboot (while installing the update from the ISO file) there's a boot error (probably caused by the unsigned driver) and Windows is rolled back to the previous build. You have to delete all the modded drivers using software like this.

The 64bit Intel RSTe AHCI & RAID drivers v16.0.2.1086 WHQL Are no good on the ICH10R with Windows 10 64bit Creator's spring update. It will cause bluescreens with ACPI.sys and IrqL Less than or equal to errors or other system files causing a BSOD kinds of errors.


The ones that do work are the Universal 64bit Intel RSTe AHCI+RAID drivers v16.0.1.1018 mod+signed by Fernando they have not caused an issue yet.

my system works fine with windows 10 1803 pro, using v16.0.2.1086 drivers, i also installed 24 intel microcode, if i see some bugs i will report in this thread, i also use samsung rapid mode with 16gb 2133 cas 11 ram without any pagefile, superfetch And Hibernation

Its the onboard SATA controller for the ASUS P5Q Deluxe without the WIFI. It has the ICH10R in AHCI mode. It has a PNY 120GB SSD on Port 4. When I used the older Intel driver that is supposed to be supported for windows 7 it would at random hang the system like the drive was very busy at reading or writing. It seems to only effect the older versions of Windows 10. Using the v16 driver fixed that problem. Its for my brother's computer and I have an identical system when we built them in 2009. He refuses to upgrade for some reason. I wonder if I just buy a ASmedia SATA card to get SATA 3.0 would be more worth it.

it works fine on my PC

Using ASUS P5P43TD-PRO Windows 10 Pro X64 Insider Fast Ring 1803
I'm using ICH10R in AHCI mode on my HDD

no bsod or performance lost ,Works great on 13.44 Ahci Driver

Hi! I'm a user of an old Dell 1520 (ICH8M, DEV_2829) and now that I switched it over to an SSD I installed your modded v14.8.18.1066, and it all works fine! Thank you for your work!

Is it possible to also install the corresponding RST software? I've tried but since it ships with the unmodded drivers installation fails claiming it's an unsupported platform. I tried extracting the MSI installer but it doesn't seem to work the usual way (msiexec /a ....), could we repack those installers somehow?