| Last online: 03.29.2017
you can extract the recovery module in the boot block partition (02) of the UEFI module.
open it up with your hex editor, you will find the names for the rom or hdr file there.
first of all, disconnect the cd-rom and harddrive phsyically from your notebook.
warning: the connector for the harddrive is a little bit fragile ->
pull on the right and left foots to open it up.
now pull the ribbon cable out.
if you are unsure, you can use this owner guide from the dell website.
format a usb stick with RUFUS.
Select first the USB stick you want to format.
Warning: All data on this USB stick will be lost.
Use MBR partition scheme for BIOS or UEFI, FAT32 (Default), Cluster Size 8192 bytes (Default).
The volume label doesn't matter.
Set a tick at quick format.
Untick "Create a bootable disk using..."
Untick "Create a extended label and icon files"
Download the UEFI version that was at last on your notebook.
if it was version A07, then download A07.
if it was version A10, then download A10.
Extract from 3350A10.exe / 3350A07.exe the UEFI file.
Open up a cmd and enter the following command: 3350A10.exe /writehdrfile
Rename the rom file to 3350.hdr and move it on the usb stick.
Disconnect the battery from your notebook.
Plug In the pendrive.
Press the end key and hold it down.
Connect the charger (still hold END).
The notebook starts automatically and shows the recovery screen.
Press enter and wait until finish the flashing.
Press any key to restart.
The first restart attempt wouldn't be successful.
The second one would work.
Give it a little bit time between the start attempts.
ah i see, it's the recovery module in Volume 02.
i opened it in the hex editor:
the name of the recovery rom seems to be 3350.hdr or DN13A10.rom.
however, there is nothing shown on the screen if i follow the recovery procedure.
In the same file the El Torito specification is mentioned...
maybe that's the right way.
i believe, the filesystem module for fat32 isn't integrated into this UEFI.
integrate the filesystem module into the UEFI and try again to load the UEFI Shell.
replace the ePSA (Enhanced Pre-Boot System Assessment) Test Module against a UEFI Shell.
Anybody experience with that?
thanks for your hints.
i begin to edit the options.
I edited the Array to unlock the other tabs:
010100010101000000000000 <- original
010101010101010101010101 <- with intel
Then i switched the following bits:
0A 82 46 02 <- true
0A 82 47 02 <- false
1E 82 46 02 <- true
0A 82 47 02 <- false
Can someone take a look @ my setup-ifr.txt file? Thanks!
Thanks for your help, i try to transfer the old config file, however, get now the following errors:
PAGE TV Features: $Under_Over_Scan_Via_DVI : Unable to find symbol.
PAGE Device 1: $Int_EFP1_Dongle_Detect : Unable to find symbol.
PAGE Device 2: $Int_EFP2_Dongle_Detect : Unable to find symbol.
PAGE Device 3: $Int_EFP3_Dongle_Detect : Unable to find symbol.
Found also a hint, but my russian is really rusty:
What's your recommondiation?
Hey @SoniX ,
thanks for this great Tutorial.
However, i have a question:
I have a Dell Vostro 3350 Notebook with a Intel Core i5-2410M - Sandy Bridge CPU.
I try to update my vbios for my HD 3000 at the moment.
Version VBT: A1 00
size VBT: 0F 61
Version OROM: 2098
I looked ath the 'Table VBT OROM VBIOS Version and Size.docx' file.
There is a VBT with the Version A1 00 available but the filesize doesn't fit.
So i'm unsure, what to do.
Maybe you or someone can take a look at my bios/vbios?
Edit: Inserted VBIOS